Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Star-Dasher Crank Churn: Geared Crank and Flywheel Drive Two Notched Dashers Set Point Over Gap
Lorenzo Lake of Middlebury, Pennsylvania, received US 24,845, dated 19 July 1859, for an upright dash churn worked by gearing so that a child could churn even a very large churn. A handle turns a large wheel driving a wheel half its size on a crank shaft with a balance wheel; the crank's pitman works the staff up and down through a guide. The staff carries two dashers of boards with V-shaped slots in their ends, set so the points of one lie over the gaps of the other, cutting the cream as it escapes going down and up and dashing it against the sides.
This rung builds it with printed gears over a 20-litre bucket.
Średniozaawansowany
About 2 days, plus printing
Instrukcje
1
1
Strokes per turn of the handle
Strokes per turn of the handle
Wczytywanie notatnika Jupyter…
2
2
A crank and pitman working the staff, before it
A crank and pitman working the staff, before it
Dorsey's pitman also turned the staff. Lake's only lifts it, through gearing and a balance wheel for speed.
3
3
Read US 24,845
Read US 24,845
"... these dashers are so placed upon the staff that the sharpened ends of the boards thus cut, will cover the spaces left between the boards in the dasher immediately above or below—so that when operated in the churn the cream will be more thoroughly cut and the globules will be more easily and speedily broken."
4
4
Print the wheel E
Print the wheel E
The 40-tooth wheel for the handle's shaft. PETG, 0.2 mm layers, 50 % infill, 5 walls.
5
5
Print the wheel F
Print the wheel F
The 20-tooth wheel for the crank shaft. PETG, 0.2 mm layers, 50 % infill, 5 walls.
6
6
Platform, upright and frame
Platform, upright and frame
Screw a pine platform C 500 x 550 mm. Stand a 70 mm upright C' 990 mm tall at its back, braced. Screw a hardwood beam 130 x 255 x 40 mm out from the upright's top toward the front, and hang three hardwood blocks from it, each bored 20.5 mm 900 mm above the floor: two either side of the crank, 90 mm apart, for shaft G, and one 90 mm to the side for wheel E's shaft. Screw a hardwood guide arm I from the upright to over the bucket 430 mm up, with a 26 mm square hole.
Materiały do tego kroku:
Deska sosnowa2 sztuk
Drewno iglaste 70x70 mm2 sztuk
Deska z drewna liściastego2 sztuk
Wkręt do drewna nr 10 x 3"20 sztuk
Klej do drewna1 sztukaPotrzebne narzędzia:
Piła ręczna
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł łopatkowych
Dłuta
Poziomica
Miara zwijana7
7
Crank shaft G, wheels and handle
Crank shaft G, wheels and handle
Make the crank from two hardwood webs 30 x 10 mm, a 12 mm stainless pin 50 mm off the axis between them, and two 20 mm steel stubs, one each side, run through the hanging blocks. Fix wheel F on the rear stub and a plywood balance wheel B 300 mm across, with spokes, on the front stub. Run a 20 mm steel shaft through the third block with wheel E meshing with F, and a hardwood handle M 57 mm long with a dowel grip on its end.
Materiały do tego kroku:
Deska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnej1 sztuka
Pręt stalowy surowy2 sztuk
Filament PETG1 sztuka
Płyta sklejkowa1 sztuka
Kołki z twardego drewna1 sztuka
Klej do drewna1 sztuka
Zestaw śrub sześciokątnych4 sztuk
Nakrętka samohamowna z wkładką nylonową4 sztukPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Wyrzynarka
Piła do metalu
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Pilniki (pilnik ręczny)
Klucz nastawny8
8
Staff, dashers and pitman
Staff, dashers and pitman
Cut two plywood dashers L, each a 16-point star 250 mm across with its notches 20 mm deep, and a 25 mm square hole in the middle. Glue them on a 25 mm square hardwood staff D 150 mm apart, the upper turned half a point from the lower. Cut a hardwood pitman H 300 mm between centres with a fork at its foot; fit a hardwood thimble J on the staff's top and push an 8 mm stainless rod a through the fork, thimble and staff. Put the staff through the guide and the bucket's lid and set the lower dasher 25 mm off the floor at the bottom of the stroke.
Materiały do tego kroku:
Płyta sklejkowa1 sztuka
Deska z drewna liściastego2 sztuk
Klej do drewna1 sztuka
Pręt ze stali nierdzewnej1 sztuka
Podkładka płaska2 sztuk
Wiadro 20-litrowe1 sztukaPotrzebne narzędzia:
Wyrzynarka
Piła ręczna
Dłuta
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Papier ścierny9
9
The build in 3D
The build in 3D
FreeCAD model of this build, half the bucket cut away: the platform and upright, the beam with its hanging blocks, the split crank shaft with balance wheel and wheel F, wheel E and handle M, the forked pitman and thimble, the staff through its guide, and the two star dashers. It was checked at eight crank angles.
10
10
Churn
Churn
Pour about 10 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, and put the lid on round the staff. Turn the handle steadily and time it. When the butter comes, pull pin a, lift the staff out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka10 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej11
11
Troubleshooting
Troubleshooting
Star-dasher churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Lorenzo Lake** of Middlebury, Tioga County, Pennsylvania, assignor to himself and William Patton of Towanda, US 24,845, 19 July 1859, "Churn". He claimed the dasher L worked by the devices described, not the gearing as such. His only proportion is wheel F about half wheel E. His dashers are boards with V-slotted ends; ours are plywood stars cut to the same pattern. Every size is ours.
Materiały
17- 2 sztukZastępnik
- 2 sztukZastępnik
- 2 sztukZastępnik
- 20 sztukZastępnik
- 3 sztukZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 4 sztukZastępnik
- Zastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
17- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
3Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.



