Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Opposed Perforated-Paddle Churn: Sloping Holed Paddles on a Geared Shaft Pass Between Paddles Sloping the Other Way on Slide Bars
Buttercup

Autor

Buttercup

11. listopad 2026IE
6
0
0
0
0

Opposed Perforated-Paddle Churn: Sloping Holed Paddles on a Geared Shaft Pass Between Paddles Sloping the Other Way on Slide Bars

John R. Mickey of Waterford, Pennsylvania, received US 31,554, dated 26 February 1861, for a churn meant to churn sweet milk quickly. Perforated paddles on a geared upright shaft slope one way and pass between perforated paddles fixed round the tub that slope the other way, so the turning set lifts the milk while the fixed set drives it down, forcing it through the holes. The fixed paddles stand on dovetailed bars that slide out of grooves on the tub's wall for cleaning and for gathering the butter. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 3 days

Instrukcje

1

Paddles that pass without touching

Wczytywanie notatnika Jupyter…
2

Wings sloping opposite ways passing each other, seven months before

Bissell's two dashers carry wings sloping opposite ways. Mickey fixes one set to the tub and perforates both.
3

Read US 31,554

"The inclination of paddles E. has a tendency to continually elevate the milk while the tendency of paddles F. is opposite and the consequence is that the milk is greatly agitated and so acted upon that the globules are rapidly broken and butter produced in an incredibly short time."
4

Tub A, retaining strips d and slide bars c

Use a 20-litre food-grade bucket as the tub A, with its bottom as C. Plane three hardwood slide bars c 330 mm long to a dovetail section, 20 mm across the inner face, 26 across the back, 11 thick. For each, cut two hardwood strips d 20 mm wide, 300 long, bevelled on one edge to hold the dovetail, and tapered behind to the bucket's wall; screw them to the wall from outside a third of a turn apart, 30 mm above the floor, so the bar slides down between them to rest on the floor. Seal the screw holes.

Materiały do tego kroku:

Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Wkręty do drewnaWkręty do drewna18 sztuk
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Frezarka górnowrzecionowaFrezarka górnowrzecionowa
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
5

Print the lowest fixed paddle F (three)

A fixed paddle F: 60 x 50 x 6 mm with a 12 and a 9 mm hole. Print three. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the middle fixed paddle F (three)

As the lowest, 42 mm wide. Print three. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Print the top fixed paddle F (three)

As the lowest, 34 mm wide. Print three. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
8

Fixed paddles F on the bars

Chisel three slots 6 mm wide and 4 deep across the inner face of each bar, at 60, 160 and 260 mm from its foot, sloping 70 degrees from flat, all the same way. Glue the paddles F into them with food-safe silicone and a screw each, widest at the bottom, so they reach in to 70 mm from the tub's centre.

Materiały do tego kroku:

Filament PETGFilament PETG1 sztuka
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka
Wkręty do drewnaWkręty do drewna9 sztuk

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wkrętakówZestaw wkrętaków
9

Print the lowest turning paddle E

A turning paddle E: 101 x 45 x 6 mm with 12, 10 and 8 mm holes. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
10

Print the middle turning paddle E

As the lowest, 40 mm wide. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
11

Print the top turning paddle E

As the lowest, 35 mm wide. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
12

Print the bearing in the bottom C

The bearing on the bucket's floor: 50 mm across, 12 high, with a 16.8 mm hole 8 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
13

Shaft D and turning paddles E

Turn a hardwood shaft D 28 mm across and 318 mm long. Set a 10 mm stainless pin 7 mm out of its foot and a 16 mm stainless rod 144 mm long 20 mm into its top. Chisel three slots through it 6 mm wide, sloping 70 degrees from flat the other way from the F paddles, at 98, 198 and 298 mm above its foot, the second a ninth of a turn and the third two ninths round from the first, and glue the paddles E in with silicone and a cross pin, so they reach 115 mm from the centre.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Filament PETGFilament PETG1 sztuka
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Tokarka do drewnaTokarka do drewna
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
14

Print the pinion

The pinion on the shaft's top: 14 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
15

Print the driving wheel

The driving wheel on the crank shaft: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
16

Lid B, cross bar, gearing and crank

Cut a 12 mm HDPE lid B to the bucket's top with a 20 mm hole in the middle. Screw two hardwood ears 30 x 40 mm, 105 long, to opposite sides of the bucket's top, standing 45 mm above its rim. Cut a hardwood cross bar 370 x 140 x 25 mm, notched at its ends to drop over the ears, bored for stainless pins through ears and ends and 16.6 mm at the centre. Screw two hardwood bearing blocks 50 x 25 x 108 mm on it, one 60 to 85 mm in front of the centre and one 25 to 50 behind, bored 16.6 mm across 83 mm up. Stand the shaft on its bearing with the lid and cross bar over it, pin the pinion on its top with its teeth 30 mm above the bar, run a 16 mm stainless crank shaft 180 mm long through the blocks with the driving wheel pinned on meshing the pinion, a shaft collar, and a crank of mild steel flat bar, 100 mm throw, with a hardwood handle.

Materiały do tego kroku:

Płyta HDPEPłyta HDPE1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Wkręty do drewnaWkręty do drewna12 sztuk
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej3 sztuk
Shaft CollarShaft Collar1 sztuka
ZawleczkaZawleczka4 sztuk
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
KompasKompas
WyrzynarkaWyrzynarka
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Zestaw wkrętakówZestaw wkrętaków
17

The build in 3D

FreeCAD model of this build, the bucket cut open: three dovetail slide bars in their strips, each with three sloping perforated paddles, the shaft with three paddles sloping the other way, the bearing, lid, cross bar, gears and crank.
Plik projektowyBLENDCC0 - Free
18

Churn and gather

Pour about 14 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket with the paddles in, put on the lid and drop the cross bar over the ears, pinning it. Turn the crank briskly, timing it. When the butter comes, lift off the gearing and lid, draw the three slide bars up out of their strips, and turn the shaft slowly by hand so the butter gathers on its paddles. Lift it out, take off the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it. Before putting the bars back, push them down so any butter lodged in the grooves is forced out at the bottom.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka14 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
19

Troubleshooting

Opposed-paddle churn troubleshooting.

Flow

Loading...
20

History and honest limits

**John R. Mickey** of Waterford, Erie County, Pennsylvania, US 31,554, 26 February 1861, "Churn". He claimed "the stationary, perforated paddles F. in combination with the rotating perforated paddles E; when the two sets of paddles (F and E) consist of simple planes, and are arranged obliquely in opposite directions", and disclaimed the tapering solid paddles of John O'Neil's rejected application of 24 June 1852. He made the churn for sweet milk and wrote that "from three gallons of sweet milk three and a quarter pounds of butter" came "in three and a half minutes"; we have not tested that, and we churn cream. He gives the paddles' slope only as "about 70"; we read it from Figs. 2 and 3 as 70 degrees from flat. He left the gearing to "any of the known ways"; ours is a printed crown wheel and pinion. Every size here is ours.

Materiały

14

Wymagane narzędzia

19

Pliki projektowe

10

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...