Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Festooned Kite: Three Tailless Kites on One 7 ft Spruce Spine With Tissue-Paper Fringes (Boy Mechanic, 1919)
Spartan

Autor

Spartan

13. listopad 2026NO
7
0
0
0
0

Festooned Kite: Three Tailless Kites on One 7 ft Spruce Spine With Tissue-Paper Fringes (Boy Mechanic, 1919)

C. M. Miller's compound kite from The Boy Mechanic, Book 3 (1919): three tailless kites, 3 ft, 2 ft and 1 ft wide, strung on one 7 ft spruce spine, covered in tissue paper and hung with fringed tissue festoons from the ends of the sticks. An 87 in bridle sets it to the wind.
Średniozaawansowany
About 1 day

Instrukcje

1

Spine stations and string lengths

Wczytywanie notatnika Jupyter…
2

Read The Boy Mechanic, Book 3

"More than one kite on the same framework is known as a compound kite. The one illustrated consists of three tailless kites on one long stick, called the spine."
3

Cut the sticks

Cut the spine of straight-grained spruce (or pine or bass) without a twist, 7 ft long by 1/4 by 1/2 in; if the wood breaks easily make it 3/4 in wide, or 3/8 in thick. Cut the bows 4 ft by 1/4 by 1/2 in, 2 ft by 1/4 by 3/8 in, and 1 ft by 1/4 by 1/4 in. A twisted spine keeps the three kites out of one plane and makes the kite unsteady.

Materiały do tego kroku:

Listwa z drewna iglastegoListwa z drewna iglastego4 sztuk

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Strug ręcznyStrug ręczny
Miara zwijanaMiara zwijana
OłówekOłówek
4

Lash on the bows

Lash the upper bow 13 in from the top of the spine, its ends 6 in past the kite for the festoons; then the centre bow 5 in below D and the lower bow as in the drawing (6, 7, 29, 5, 19, 2, 10 and 6 in down the spine). Lash, do not nail: wind diagonally both left and right round the two sticks, then wind between them round the other windings to draw everything tight.

Materiały do tego kroku:

Sznurek do latawcaSznurek do latawca1 sztuka

Potrzebne narzędzia:

Miara zwijanaMiara zwijana
OłówekOłówek
NożyczkiNożyczki
5

String the outlines

Drill small holes (or notch with a knife or saw) in the spine 6 in from the top at A, 6 in from each end of the upper bow at B and C, and 29 in below the upper bow at D. Tie the outline at A and pass it through C, D and B back to A; draw it tight without springing spine or bow. Check that AC equals AB and CD equals BD, shift the string until they do, and wind each point (E) so it cannot slip. String the centre and lower kites the same way.

Materiały do tego kroku:

Sznurek do latawcaSznurek do latawca1 sztuka

Potrzebne narzędzia:

Wiertarka ręcznaWiertarka ręczna
Stalowy nóż składanyStalowy nóż składany
Miara zwijanaMiara zwijana
6

Cover and fringe

Cut the tissue about 1 in larger all round than each kite, turn over about half the allowance and paste it, leaving the cover loose. French tissue comes in fine colours and is stronger than common tissue; Chinese rice paper is strongest but only natural colour. For the festoons cut tissue strips 2-1/2 in wide, paste 1/2 in of one long edge over a string, and slit the loose edge every 1 in. Hang the festoons from the stick ends in easy curves, not tight, keeping both sides balanced.

Materiały do tego kroku:

Bibuła kolorowaBibuła kolorowa5 arkuszy
Klej pszennyKlej pszenny1 sztuka
Sznurek do latawcaSznurek do latawca1 sztuka

Potrzebne narzędzia:

NożyczkiNożyczki
Pędzel do klejuPędzel do kleju
LinijkaLinijka
7

Bow the kites and bridle

Tie a string from end to end of the upper and centre bows on the back and spring in short brace sticks to bend them, as usual for tailless kites. Tie the 87 in bridle at A and to the spine at F, and attach the kite line 30 in from A, leaving 57 in to F.

Materiały do tego kroku:

Sznurek do latawcaSznurek do latawca1 sztuka
Listwa z drewna iglastegoListwa z drewna iglastego1 sztuka

Potrzebne narzędzia:

Stalowy nóż składanyStalowy nóż składany
Miara zwijanaMiara zwijana
8

Flying and troubleshooting

Festooned kite flying.

Flow

Loading...
9

History and honest limits

From "How to Make Combined Kites, Part II: A Festooned Kite" by C. M. Miller, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 155-156). He does not name the string, the paste or the kite line. The tools and metric figures are ours.

Materiały

4

Wymagane narzędzia

9

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...