Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Dog Kennel Whose Top Tilts Back on Lift-Off Hinges to Air and Clean It (Minion, 1909)
Woody

Autor

Woody

13. listopad 2026NO
6
0
0
0
0

Dog Kennel Whose Top Tilts Back on Lift-Off Hinges to Air and Clean It (Minion, 1909)

John S. Minion of Newark received US 920,975, dated 11 May 1909, for a kennel in two parts. The top half, with the roof, sits on the bottom half and hinges at the back on slotted plates and studs, so it can be tilted back to let the sun in and clean the floor, or lifted right off. A swinging arm drops down by itself to hold it open. We build it from pine. All sizes are ours.
Średniozaawansowany
About 1 day

Instrukcje

1

Size for the dog

Wczytywanie notatnika Jupyter…
2

Read US 920,975

"The upper portion can be tilted back as shown in Fig. 1 so as to permit the cleaning of the lower portion, and also allow sunlight to penetrate therein over its whole surface, which makes a sanitary structure."
3

Build the lower portion

Build an open box of pine boards with upright sides and a floor, his portion 10, raised on two strips 12 so air passes under it. Cut the entrance 11 in the front.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 sztuka
Gwoździe ocynkowaneGwoździe ocynkowane1 sztuka

Potrzebne narzędzia:

Miara zwijanaMiara zwijana
Piła ręcznaPiła ręczna
Piłka włosowaPiłka włosowa
Młotek ciesielskiMłotek ciesielski
4

Build the upper portion

Build the top half, his portion 13, with sides that stand on the lower sides, a gabled roof 16, and an opening 15 matching the entrance. Nail strips 14 round its lower edge outside so they overlap the lower portion, shed water and make a tight joint.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 sztuka
Gwoździe ocynkowaneGwoździe ocynkowane1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Piłka włosowaPiłka włosowa
Młotek ciesielskiMłotek ciesielski
5

Fit the lift-off hinge

Screw a flat-bar plate to the back of each lower side, projecting behind, with a slot cut in its top edge (his plates 32 and slots 33). Screw a plate with a bolt as a stud to each side of the upper portion so the studs drop into the slots when the top is set down (his plates 34 and studs 35). The top now tilts back on the studs or lifts off.

Materiały do tego kroku:

Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Śruba zamkowaŚruba zamkowa1 sztuka
Wkręty do drewnaWkręty do drewna1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Zestaw pilnikówZestaw pilników
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
6

Fit the prop arm

Hang a flat-bar arm from a hinge at the top of the back of the upper portion (his arm 24 and hinge 23). Join its lower part to a bracket on the lower portion with a link (his link 25 and bracket 28), slotted so it can be unhooked. When the top is tilted back, the arm swings down to the ground and props it.

Materiały do tego kroku:

Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Zawias czopowyZawias czopowy1 sztuka
Śruba zamkowaŚruba zamkowa1 sztuka
Wkręty do drewnaWkręty do drewna1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
7

Protect the entrance

Screw a strip of flat bar round the edge of the entrance, his iron band 31, where a chained dog wears it.

Materiały do tego kroku:

Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Wkręty do drewnaWkręty do drewna1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
8

Troubleshooting

Kennel troubleshooting.

Flow

Loading...
9

History and honest limits

**John S. Minion** of Newark, US 920,975, dated 11 May 1909, filed 21 May 1908. He claimed "a kennel comprising a bottom portion having vertical sides, a top portion with vertical sides resting on the sides of the bottom portion, hinges connecting the sides of the bottom and top portions on one end, an arm swinging from its top end on the hinged end of the top portion, and a link pivoted to the bottom portion and to the arm". He gives no sizes; the pine, all sizes and the flat-bar and bolt fittings are ours.

Materiały

6

Wymagane narzędzia

9

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...