Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)
Forge

Autor

Forge

13. listopad 2026NO
13
0
0
0
0

Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)

Frank L. Pritchard of Parker, Arizona, received US 2,231,593, dated 11 February 1941, for a tubing cutter small enough for a mechanic's tool box. The tube sits in a V in a fixed jaw. A movable jaw slides on the adjusting screw and a guide pin, with a spring pushing the jaws apart. The cutting wheel is held by a pivoted support with threads on its inner edge. Swung down, the support lets go of the screw, so the jaw can be pushed straight onto any tube. Swung up, it meshes with the screw again and the screw feeds the wheel in. We make his parts from steel bar and plate. All sizes are ours.
Średniozaawansowany
About 3 days

Instrukcje

1

The swing that lets go

Wczytywanie notatnika Jupyter…
2

Read US 2,231,593

"The pivoted blade support 16 may swing downwardly until the threads thereof will be free of the threads of the screw 8. The movable jaw 6 may now be slid downwardly until the pivoted blade support is in its proper cutting position."
3

Print the template

Both jaws, the blade support, the wheel and a 15 mm tube at 1:1, with the screw, pin and pivot holes. print at 100 % (check the 50 mm bar).
Plik projektowyPDFCC0 - Free
4

Make the stationary jaw

Saw 64 mm of 16 mm square bar, or of 16 mm plate. File the 90 degree V 8 mm deep in its top face. Drill the 6 mm pin hole and a 10 mm hole for the screw, and counterbore the pin hole 10 mm across, 5 mm deep, for the spring. Drill the 3 mm cross-pin hole across the jaw so it just cuts into the side of the screw hole.

Materiały do tego kroku:

Blacha gruba ze stali niskowęglowejBlacha gruba ze stali niskowęglowej1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Zestaw pilnikówZestaw pilników
Wiertarka stołowaWiertarka stołowa
Imadło maszynoweImadło maszynowe
Zestaw wiertełZestaw wierteł
PunktakPunktak
Rysik traserskiRysik traserski
Imadło warsztatoweImadło warsztatowe
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
5

Make the movable jaw and the support

Saw the movable jaw 50 mm long from the same bar. Drill the 6.2 mm pin hole and its spring counterbore. Saw and file a slot 8.2 mm wide down its middle, from 22 mm to the end. Saw the blade support from 14 mm plate to the template. File its upper part down to 8 mm thick, centred, so it slides into the slot, and file away its lower inner corner. Saw a 7 mm slot up its lower part for the wheel. Drill the pivot and stop-pin holes through the jaw and support together, and file the stop-pin hole in the support into a short slot.

Materiały do tego kroku:

Blacha gruba ze stali niskowęglowejBlacha gruba ze stali niskowęglowej1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Zestaw pilnikówZestaw pilników
Zestaw pilników iglakówZestaw pilników iglaków
Wiertarka stołowaWiertarka stołowa
Imadło maszynoweImadło maszynowe
Zestaw wiertełZestaw wierteł
Imadło warsztatoweImadło warsztatowe
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
6

Tap the half nut

Pin the support in the jaw, swung up, and clamp it there. Drill 6.8 mm down the screw axis through both, so the drill cuts a shallow groove in the support's inner edge, then tap it M8 through both. Take the support out and open the jaw's own hole to 8.5 mm, so the screw passes freely and only the support's threads hold it.

Potrzebne narzędzia:

Wiertarka stołowaWiertarka stołowa
Imadło maszynoweImadło maszynowe
Zestaw wiertełZestaw wierteł
Zestaw do gwintowaniaZestaw do gwintowania
Olej do cięciaOlej do cięcia
7

Make the screw and the guide pin

Turn the top 62 mm of a 90 mm piece of 10 mm bar to 8 mm and cut an M8 thread on it with the die. Turn a groove 1.5 mm deep and 3.2 mm wide in the plain part, where the cross pin will sit, and drill a 6 mm hole across its bottom end for a T-bar. Cut the guide pin, 80 mm of 6 mm rod, and drill a 3 mm hole across its top for the stop pin.

Materiały do tego kroku:

Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej1 sztuka
Pręt ze stali niskowęglowejPręt ze stali niskowęglowej1 sztuka

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
Uchwyt tokarski 3-szczękowyUchwyt tokarski 3-szczękowy
Nóż tokarskiNóż tokarski
Przecinak tokarskiPrzecinak tokarski
Zestaw do gwintowaniaZestaw do gwintowania
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
8

Turn the cutting wheel

Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.

Materiały do tego kroku:

Pręt ze stali narzędziowejPręt ze stali narzędziowej1 sztuka

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
Uchwyt tokarski 3-szczękowyUchwyt tokarski 3-szczękowy
Nóż tokarskiNóż tokarski
Przecinak tokarskiPrzecinak tokarski
Zestaw nawiertakówZestaw nawiertaków
Zestaw wiertełZestaw wierteł
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
Okulary ochronneOkulary ochronne
9

Harden and temper

Heat the wheel to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.

Potrzebne narzędzia:

Palenisko kowalskiePalenisko kowalskie
Kleszcze kowalskieKleszcze kowalskie
Mały magnesMały magnes
Kadź hartowniczaKadź hartownicza
WodaWoda
OsełkaOsełka
Rękawice spawalniczeRękawice spawalnicze
Okulary ochronneOkulary ochronne
10

Assemble

Drive the guide pin into the stationary jaw. Put the screw into its hole from below and drive the cross pin in so it lies in the groove; the screw must still turn. Fit the T-bar. Slip the spring over the guide pin, then the movable jaw over the pin and the screw, and put the stop pin across the top. Fit the wheel in the support on its 5 mm pin, and pin the support into the jaw with its pivot and stop pins. Rivet a 1.5 mm steel strip along the top of the jaw, sticking out past the support as a thumb piece. Oil the threads.

Materiały do tego kroku:

Kołek stalowyKołek stalowy5 sztuk
Zestaw sprężyn naciskowychZestaw sprężyn naciskowych1 sztuka
Taśma ze stali sprężynowejTaśma ze stali sprężynowej1 sztuka
Nity staloweNity stalowe2 sztuk
Pręt ze stali niskowęglowejPręt ze stali niskowęglowej1 sztuka

Potrzebne narzędzia:

Młotek ślusarski z kulistym rąbemMłotek ślusarski z kulistym rąbem
PunktakPunktak
Imadło warsztatoweImadło warsztatowe
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Olej do cięciaOlej do cięcia
11

Cut a copper tube

Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Swing the support down, push the movable jaw down until the wheel touches the tube in the V, swing it up into the screw, and tighten the screw a little. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.

Materiały do tego kroku:

Rura miedzianaRura miedziana1 sztuka

Potrzebne narzędzia:

Imadło warsztatoweImadło warsztatowe
GradownikGradownik
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
12

Troubleshooting

Swing-nut tubing cutter troubleshooting.

Flow

Loading...
13

History and honest limits

**Frank L. Pritchard** of Parker, Arizona, US 2,231,593, dated 11 February 1941, filed 17 November 1939. He claimed "a pivoted blade support mounted on the movable jaw and having threads on the inner edge thereof adapted to engage the threads of said screw". His movable jaw had a bushing for the guide pin and a looped handle on the screw head; ours has a drilled hole and a T-bar. The patent gives no sizes or materials; all of ours are ours.

Materiały

9

Wymagane narzędzia

27

Pliki projektowe

1

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...