SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Rocking Twin-Dasher Lever Churn: One Lever Rocks the Box and Works Two Dashers Through a Perforated Wall
A. C. Stiles of South Bloomfield, Ohio, received US 3,764, dated 27 September 1844, for a rocking churn: an oblong box on rockers, split by a partition with holes, with a dasher on each side worked by arms on shafts across the ends, and one upright lever that rocks the box and works the dashers together.
This rung prints the partition, dashers and arms, builds the box and makes butter.
Zaawansowany
About 6 hours, plus printing
Instrukcje
1
1
One lever, three motions
One lever, three motions
Wczytywanie notatnika Jupyter…
2
2
Two dashers from one lever, before it
Two dashers from one lever, before it
Mitchell worked two dashers from one lever; Stiles adds rockers and a perforated partition between them.
3
3
Read US 3,764
Read US 3,764
"The machine is operated by moving the upright lever l, to and fro, which rocks the box, while at the same time it works the dashers up and down, thus throwing the cream through the partition d, till the butter is made."
4
4
Print the parts
Print the parts
Print the partition (/uploads/blueprints/rocking-twin-dasher-lever-churn-partition.stl), two dashers (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher.stl), two dasher arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher-arm.stl) and two lower arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-lower-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Materiały do tego kroku:
Filament PETG1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)5
5
Box on rockers
Box on rockers
Build a pine box about 260 × 120 × 150 mm with a close-fitting lid, sealed inside. Glue the partition across its middle and screw two curved pine rockers lengthwise underneath. Drill the lid for the two dasher handles.
Materiały do tego kroku:
Deska sosnowa1 sztuka
Klej do drewna1 sztuka
Wkręt do drewna #8 x 1"1 sztukaPotrzebne narzędzia:
Piła ręczna
Piłka włosowa
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Ściski6
6
Shafts, arms and lever
Shafts, arms and lever
Set a 10 mm square shaft across each end on two studs, 60 mm above the lid. Fit a dasher arm on each, pointing inward and pinned to its dasher's handle, and a lower arm on each outside the box. Join the lower arms with a pine bar, and pivot an upright pine lever on a block near the box's foot, pinned to the bar's middle.
Materiały do tego kroku:
Kołki z twardego drewna1 sztuka
Deska sosnowa1 sztuka
Pręt ze stali niskowęglowej1 sztuka
Śruby maszynowe1 sztukaPotrzebne narzędzia:
Piła ręczna
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wkrętaków7
7
The patent drawing
The patent drawing
US 3,764 drawing sheet, public domain (expired patent).

8
8
Rock and churn
Rock and churn
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Work the lever to and fro: the box rocks and the dashers rise and fall in turn. Keep fingers clear of the arms and the rockers. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Materiały do tego kroku:
Śmietanka kremówka1500 ml
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej9
9
Troubleshooting
Troubleshooting
Rocking twin-dasher churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**A. C. Stiles** of South Bloomfield, Pickaway County, Ohio, US 3,764, 27 September 1844. He claimed the combination of the rockers and dashers in the double-chambered churn. His drawing gives no sizes; ours are ours. FDM prints hold food in their layer lines, so wash well and replace when worn.
Materiały
11- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1500 mlZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
11- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Double-Dasher Lever Churn: Swing One Lever, One Dasher Rises as the Other Falls
autor: Woody
Obróbka drewna
7
0
0
0
0
0

Rocking-Stool Churn: Rock the Churn, the Dashers Ride With It
autor: YourGrandma
JEDZENIE I NAPOJE
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
47
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.