SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered
Forge

Autor

Forge

18. październik 2026NO
20
0
0
0
0

Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered

Needles are made from good steel wire: cut, straightened, pointed, flattened and pierced for the eye, hardened by heating and plunging into oil, then tempered back to a springy hardness, scoured and polished (Bucknall Smith, A Treatise upon Wire, 1891). This is the same sequence by hand, one heavy needle at a time from piano wire; the hand methods and sizes are ours. The picture: steel sewing needles (Wikimedia Commons).
Średniozaawansowany
Half a day

Instrukcje

1

Cut, soften and straighten

Cut 70 mm of 1.2 mm piano wire. Heat it to red in the forge and let it cool slowly in the ashes so it can be filed and drilled, then roll it straight on the anvil.

Materiały do tego kroku:

Struna fortepianowaStruna fortepianowa70 mm

Potrzebne narzędzia:

Obcinaki boczneObcinaki boczne
Kuźnia kowalskaKuźnia kowalska
Szczypce półokrągłe wydłużoneSzczypce półokrągłe wydłużone
KowadłoKowadło
2

Point

Clamp it in the vise and file a long, even taper to a sharp point, turning the wire as you go.

Potrzebne narzędzia:

Zestaw pilnikówZestaw pilników
Imadło warsztatoweImadło warsztatowe
Okulary ochronneOkulary ochronne
3

Flatten and pierce the eye

Flatten the head end slightly on the anvil, drill the eye through the flat with the finest bit, then file off the burrs and round the head.

Potrzebne narzędzia:

KowadłoKowadło
Młotek z rąbem poprzecznymMłotek z rąbem poprzecznym
Wiertarka ręcznaWiertarka ręczna
Zestaw pilnikówZestaw pilników
Imadło warsztatoweImadło warsztatowe
Okulary ochronneOkulary ochronne
4

Harden in oil

Heat the needle evenly to red and plunge it into the oil. It is now glass-hard and brittle.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Szczypce półokrągłe wydłużoneSzczypce półokrągłe wydłużone
Wanna hartownicza z olejemWanna hartownicza z olejem
Okulary ochronneOkulary ochronne
5

Temper

Reheat it in the oven to about 600 °F (315 °C) and let it cool slowly to a springy temper. If it came out crooked, straighten it with light blows of a small hammer on the anvil.

Potrzebne narzędzia:

Piec do obróbki cieplnejPiec do obróbki cieplnej
Termopara z odczytemTermopara z odczytem
KowadłoKowadło
Młotek z rąbem poprzecznymMłotek z rąbem poprzecznym
6

Scour and polish

Scour it bright with emery cloth, a little oil and soap. Wash it in hot water, dry it in sawdust, touch up the point, and polish it on the leather strop.

Potrzebne narzędzia:

Płótno szmerglowePłótno szmerglowe
Oliwa z oliwekOliwa z oliwek
MydłoMydło
TrocinyTrociny
Pasek skórzany do gładzeniaPasek skórzany do gładzenia
Zestaw pilnikówZestaw pilników

Materiały

1

Wymagane narzędzia

17

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...