SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
The Oil-Wick Fountain Brush: A Can Whose Wick Is the Brush
Woody

Autor

Woody

6. październik 2026NO
7
0
0
0
0

The Oil-Wick Fountain Brush: A Can Whose Wick Is the Brush

An oil can and a rag spill, and a brush dipped in oil drips. Preston H. Clingan of Florence, Colorado, received US 787,278, dated 11 April 1905, for "a can of very simple form which is so constructed as to prevent the possibility of spilling the contents thereof": an open thimble hangs from the can's mouth to near its bottom, a rolled burlap wick inside it is frayed above the mouth into a brush, and oil in the chamber round the thimble reaches the wick from underneath. This rung works out how high a wick can lift oil, then builds the can from a jar, a tin and burlap and weighs the oil it lays on a board.
Początkujący
About 2 hours

Instrukcje

1

How high the wick lifts

Wczytywanie notatnika Jupyter…
2

A wick that feeds oil before it

The embedded blueprint feeds oil to a bearing through a wick. Clingan turns the wick's frayed end into the brush.
3

Read US 787,278

"My object is to provide a can of very simple form which is so constructed as to prevent the possibility of spilling the contents thereof. The can includes a wick of absorbent material, which is constantly supplied with oil or other fluid within the can."
4

Make the thimble

Remove both ends of a tin can that passes through the jar's mouth with 6 mm to spare. Cut it 10 mm shorter than the jar's inside height. File the cut edges.

Materiały do tego kroku:

Puszka blaszanaPuszka blaszana1 sztuka

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
LinijkaLinijka
Skórzane rękawice roboczeSkórzane rękawice robocze
5

Cut the lip ring

Cut an aluminium ring: outside to fit inside the jar's mouth, inside to fit round the thimble. Drill it 3 mm for a filling screw.

Materiały do tego kroku:

Blacha aluminiowaBlacha aluminiowa1 sztuka

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
6

Fix the thimble

Epoxy the ring round the thimble's top and into the jar's mouth, the thimble hanging 10 mm clear of the floor. Cut a rubber washer for the filling screw.

Materiały do tego kroku:

Słoik szklanySłoik szklany1 sztuka
Epoksyd dwuskładnikowyEpoksyd dwuskładnikowy1 sztuka
Śruby maszynoweŚruby maszynowe1 sztuka
Płyta gumowaPłyta gumowa1 sztuka

Potrzebne narzędzia:

Nóż introligatorskiNóż introligatorski
Zestaw wkrętakówZestaw wkrętaków
7

Roll the wick

Roll a strip of burlap tightly until it fills the thimble, 15 mm longer than it. Push it in and fray the top 15 mm with the fingers.

Materiały do tego kroku:

Juta / tkanina workowaJuta / tkanina workowa1 sztuka

Potrzebne narzędzia:

NożyczkiNożyczki
LinijkaLinijka
8

The build in 3D

FreeCAD model of this build, not of the patent: a 90 mm jar with a 66 mm mouth, the aluminium lip ring and filling screw, a 53 mm thimble 10 mm off the floor, the burlap wick with its frayed top, and the lid.
Plik projektowyBLENDCC0 - Free
9

Oil a board and weigh it

Pour linseed oil through the filling hole to half the jar's height and wait until the wick's top darkens. Weigh a plywood board, brush it once over, and weigh it again. Turn the closed jar on its side over a rag for a minute.
Krok 9 - Image 1

Materiały do tego kroku:

Pokost lnianyPokost lniany1 sztuka
Płyta sklejkowaPłyta sklejkowa1 sztuka
Szmaty bawełnianeSzmaty bawełniane1 sztuka

Potrzebne narzędzia:

Cyfrowa waga kuchennaCyfrowa waga kuchenna
StoperStoper
Miara zwijanaMiara zwijana
10

A wick that stays dry, floods or leaks

Oil-wick fountain brush troubleshooting.

Flow

Loading...
11

History and honest limits

**Preston H. Clingan** of Florence, Colorado, assignor of one-half to John H. Todd of Cañon City, filed US 787,278 on 28 July 1904; it is dated 11 April 1905. His can is cylindrical with both ends contracted and threaded, so the cover fits either end; the thimble is soldered to an inward lip at the mouth; the wick is preferably a roll of burlap. He named oiling or polishing surfaces and cleaning windows among its uses. **Honest limits.** A jar with one threaded mouth stands in for his can. The notebook assumes a fully wetting wick and one pore size. Your weights are the result.

Materiały

10

Wymagane narzędzia

12

Pliki projektowe

1

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...