Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)
Forge

Autor

Forge

14. listopad 2026NO
8
0
0
0
0

Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)

The marking scriber Richard Thompson made for his surface gauge in Amateur Work: 1/8 in. steel or a worn-out saw file, drilled in the middle, pointed at both ends with one end bent, annealed by burying it red-hot in lime, filed round while turned in a grooved hardwood block, and the points hardened.
Początkujący
Two hours

Instrukcje

1

Read Thompson

"A worn-out saw file will answer very well, with a hole drilled through the centre to fit the bolt and pointed at each end, one of which is bent."
2

Rough the shape

Forge a flat piece of steel about 1/8 in. (3 mm) thick, or a worn-out saw file, roughly to shape: pointed at both ends, one end bent into a short hook (his fig. 30).

Materiały do tego kroku:

Płaskownik ze stali narzędziowejPłaskownik ze stali narzędziowej1 sztuka

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
KowadłoKowadło
MłotekMłotek
Szczypce kowalskieSzczypce kowalskie
3

Anneal in lime

Heat it gently to a dull red and bury it in lime to cool slowly: it is then easy to file.

Materiały do tego kroku:

Wapno gaszone (wodorotlenek wapnia)Wapno gaszone (wodorotlenek wapnia)1 sztuka

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Szczypce kowalskieSzczypce kowalskie
4

Drill and flatten

Drill a hole through the middle to fit the mounting bolt and file the flat part to an even thickness for about 1/2 in. each side of the hole.

Potrzebne narzędzia:

Wiertarka stołowaWiertarka stołowa
Imadło warsztatoweImadło warsztatowe
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
5

File it round

Cut a groove along the end of a hardwood block about 3 x 2 x 1/2 in., held end up in the vice. Lay the scriber in the groove, turn it slowly toward you with the left hand and file it round with the right. File the points quite sharp.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Imadło warsztatoweImadło warsztatowe
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
6

Harden the points

Harden the points (he gives no method; ours: heat the tips to a bright red and quench in water), then touch them up on an oilstone.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Kadź hartowniczaKadź hartownicza
OsełkaOsełka
7

Troubleshooting

Scriber troubleshooting.

Flow

Loading...
8

History and honest limits

From Richard Thompson, "How to Construct a Compound Microscope" III, **Amateur Work, Illustrated**, vol. III, p. 198 and fig. 30 (checked on the archive.org scan amateurworkillus03lond). He mounts the scriber on a mahogany surface gauge with three brass washers 3/4 in. across and 1/16 in. thick. The hardening method, metric figures and tools are ours.

Materiały

3

Wymagane narzędzia

10

Według tego planu powstaje

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...