Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Wedge-Disk Rotary Churn: A Geared Disk With Wedge Teeth Throws Cream Up Into a Collar, Slanted Holes Let the Milk Back Out
Buttercup

Autor

Buttercup

11. listopad 2026IE
9
0
0
0
0

Wedge-Disk Rotary Churn: A Geared Disk With Wedge Teeth Throws Cream Up Into a Collar, Slanted Holes Let the Milk Back Out

D. T. Ward of Mansfield, Ohio, received US 30,941, dated 18 December 1860, for a square box churn whose upright staff is spun by a crank and toothed wheels. At its foot a disk with a ring of wedge-shaped teeth cuts the cream and throws it up into a wide collar on the disk; slanted holes through the disk let the milk run back out, so a current flows through the collar while the butter gathers inside it. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days

Instrukcje

1

The disk's speed

Wczytywanie notatnika Jupyter…
2

A geared spinning dasher, two months before

Kellberg's wings throw the cream outward against a fixed disk. Ward's teeth throw it upward into a collar that holds the butter.
3

Read US 30,941

"When this disk and rim, or collar are revolved rapidly the milk is cut and agitated by the projections on the disk, and also is given an upward tendency by them. It is thrown into the collar D, and passes out at the openings s, s, s. Thus a constant stream or current is produced from the out to the inside of the collar and vice versa. The butter remains and is gathered in the collar while the milk as has been stated passes out at the openings s, s, s."
4

Box A and lid

Glue up a square hardwood box A 300 x 300 mm inside and 400 deep, sides and bottom 22 mm, joints sealed with silicone sealant. Cut a 12 mm HDPE lid to the outside, 344 mm square, with a 32 mm hole at the centre.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego3 sztuk
Klej do drewnaKlej do drewna1 sztuka
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka
Wkręty do drewnaWkręty do drewna24 sztuk
Płyta HDPEPłyta HDPE1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
5

Print the step

The step on the box's floor: 60 mm across, 15 high, with a 10.6 mm hole 9 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the disk C and collar D

Disk C and collar D in one: a 160 mm disk with a ring of twelve wedge teeth to 220 mm across, each full depth at its leading edge and sloping to nothing at its trailing edge, four 18 mm holes s slanting 40 degrees the other way, and the collar 150 mm across and 60 high on top; 28.4 mm bore. Needs a 230 mm bed. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Print the wheel F

The toothed wheel F on the staff's top: 14 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
8

Print the wheel E

The toothed wheel E on the crank shaft H: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
9

Staff B

Turn a hardwood staff B 28 mm across and 400 mm long. Set a 10 mm stainless pin 14 mm out of its foot and a 16 mm stainless rod 90 mm long 20 mm into its top. Slide the disk C on so its underside is 10 mm above the staff's wooden foot, and pin it with a dowel through its hub.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
10

Upright G, arm d, standard a, shaft H and crank

Cut a hardwood upright G 40 x 40 mm and 295 mm long, with two slots 10 mm wide and 40 long through it, and fix it upright on the middle of the box's back with two carriage bolts, washers and wing nuts, so it can be raised or lowered to set the wheels' mesh. Glue and screw a hardwood arm d 50 x 25 mm, 332 mm long, across its top, reaching over the box's centre, bored 16.6 mm there for the staff. Screw two hardwood bearing blocks 50 x 25 x 108 mm on the arm, one 60 to 85 mm in front of the staff (the standard a) and one 25 to 50 mm behind it, bored 16.6 mm across 83 mm up. Stand the staff on the step through the lid and arm, pin the wheel F on its top, run a 16 mm stainless shaft H 180 mm long through the blocks with the wheel E pinned on it meshing F, a shaft collar, and a crank of mild steel flat bar, 100 mm throw, with a hardwood handle.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Śruba zamkowaŚruba zamkowa2 sztuk
Nakrętka skrzydełkowaNakrętka skrzydełkowa2 sztuk
Podkładka płaskaPodkładka płaska2 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna8 sztuk
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Shaft CollarShaft Collar1 sztuka
ZawleczkaZawleczka3 sztuk
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Klucz nastawnyKlucz nastawny
Zestaw wkrętakówZestaw wkrętaków
11

The build in 3D

FreeCAD model of this build, the box cut open: the step, the staff with the wedge-toothed disk and its collar, the lid, and the upright G with arm d, the bearing blocks, the crank shaft, the two toothed wheels and the crank.
Plik projektowyBLENDCC0 - Free
12

Churn

Pour about 12 litres of heavy cream at about 15 °C, checked with the thermometer, into the box so it stands over the collar, put on the lid and set the wheels' mesh with the upright G. Turn the crank briskly, timing it. When the butter comes, much of it lies in the collar. Lift out the staff and disk, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka12 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
13

Troubleshooting

Wedge-disk churn troubleshooting.

Flow

Loading...
14

History and honest limits

**D. T. Ward** of Mansfield, Richland County, Ohio, US 30,941, 18 December 1860, "Churn". He claimed "the disk or wheel C, constructed as described and in connection therewith the rim or collar D", and said currents had been made before. He does not give the number of teeth or holes, or the form of his toothed wheels; ours are 12 teeth, four round holes and a printed crown wheel and pinion. His upright G had a diagonal brace; ours is bolted through slots so it can be raised or lowered. Every size here is ours.

Materiały

17

Wymagane narzędzia

19

Pliki projektowe

5

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...