Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Wicker Harvesting Baskets: the Round Willow Cob (Hasluck, 1903)
Woody

Autor

Woody

4. listopad 2026NO
10
0
0
0
0

Wicker Harvesting Baskets: the Round Willow Cob (Hasluck, 1903)

The basket-maker's round 'cob': a crowned round bottom 8 in across, flaring sides slewed to 11 in across at 11 in deep, a laid border and a rope-wrapped bow handle across the top. Variable: slewed (eight and a half pairs of stakes) or the better randed white cob (nine pairs). Source: Paul N. Hasluck, Basket Work of All Kinds (1903), pp. 48-54. Picture: Fig. 55 of the book.
Średniozaawansowany
Unknown

Instrukcje

1

Lay the slarth

Cut four sticks about 11 in long and shave them along the middle so one pair crosses the other. Lay them under your feet (Fig. 52) and tie them with two rods, one of whose butts forms a half stick, so the bottom has four and a half sticks. Work the tie-rods round to open the sticks into nine parts (Figs. 53-54), keeping a crown in the bottom.

Materiały do tego kroku:

Grubsze witki wierzboweGrubsze witki wierzbowe4 11 in
Witka wierzbowaWitka wierzbowa2 tie-rods

Potrzebne narzędzia:

Sekator jednoręcznySekator jednoręczny
Płaska deska drewnianaPłaska deska drewniana
WodaWoda
2

Slew and pair the bottom

Fill in by working two rods together (slewing), adding a rod now and then, until the bottom is 7 1/2 in across; then pair off with two pointed rods to 8 in. Push the ends in, pick the bottom and cut the sticks off with the shears.

Materiały do tego kroku:

Witka wierzbowaWitka wierzbowa1 slewing, pairing

Potrzebne narzędzia:

Sekator jednoręcznySekator jednoręczny
NożyceNożyce
3

Stake and upset

Push in eight and a half pairs of stakes, one each side of eight sticks and one by the ninth. Prick them up and gather them in a hoop several times larger than the bottom, since the cob needs a 3 in spring at the border. Drive them level with the iron. Upset with the tops of four rods (7 to 9 in of tip cut off), each in front of three stakes and behind the fourth; after one round drop to three rods, each in front of two and behind the third, and piece the butts.

Materiały do tego kroku:

Kołki wierzboweKołki wierzbowe17 8 1/2 pairs
Witka wierzbowaWitka wierzbowa7 upsetting

Potrzebne narzędzia:

Sekator jednoręcznySekator jednoręczny
MłotekMłotek
PrzewlekaczPrzewlekacz
4

Slew the sides

Pin the bottom to the board with the small bodkin or weight it, and fill in the stakes with a three-rod slew (Fig. 55), adding a butt inside as each top finishes outside. Let the sides spring gradually to 11 in across at 11 in deep; a round of white rods halfway up brightens it. Level with a two- or one-rod slew and pair off with two rods.

Materiały do tego kroku:

Witka wierzbowaWitka wierzbowa1 slewing

Potrzebne narzędzia:

PrzewlekaczPrzewlekacz
MłotekMłotek
5

Border and bow handle

Push two pointed sticks down the slewing at opposite sides to keep the handle place. Lay down five stakes and border as for a square basket (Fig. 56), finishing by cramming. Wet the two sticks with the sponge and pull them out; point, bend and push in a stick for the bow handle and wrap it with twisted rods as for the square basket.

Materiały do tego kroku:

Grubsze witki wierzboweGrubsze witki wierzbowe1 bow
Witka wierzbowaWitka wierzbowa4 handle wrap

Potrzebne narzędzia:

GąbkaGąbka
Sekator jednoręcznySekator jednoręczny
Grubsze witki wierzboweGrubsze witki wierzbowe

Materiały

3

Wymagane narzędzia

8

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...