Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Woven Harvesting Basket: the Square Willow Basket with Bow Handle (Hasluck, 1903)
Woody

Autor

Woody

4. listopad 2026NO
9
0
0
1
0

Woven Harvesting Basket: the Square Willow Basket with Bow Handle (Hasluck, 1903)

A sturdy square willow basket with a rope-wrapped bow handle over the open top, for carrying and gathering: the basket-maker's 'grocer's square basket'. Bottom 17 x 11 in, sides 11 in deep to the wale, corner sticks, a foot rim and a handle about 20 in high. Source: Paul N. Hasluck, Basket Work of All Kinds (1903), pp. 27-47. Picture: Figs. 48-51 of the book.
Zaawansowany
Unknown

Instrukcje

1

Weave the bottom in the screw-block

Wet the sticks an hour ahead. Cut six sticks 20 in long (3 in extra for the block), the two outside ones thicker. Set the outside pair 11 in apart in the screw-block, the four inside evenly between, thick and thin ends alternating (Fig. 33). Start with two osiers worked together, then weave one rod at a time, butts behind odd sticks, checking the 11 in width with a bent gauge rod and tapping the weave close with the iron, to 17 in long. Lock the end with one long rod (Fig. 34), take it out and pick off the ends.

Materiały do tego kroku:

Grubsze witki wierzboweGrubsze witki wierzbowe6 20 in
Witka wierzbowaWitka wierzbowa1 weavers

Potrzebne narzędzia:

WodaWoda
NożyceNożyce
Sekator jednoręcznySekator jednoręczny
MłotekMłotek
Płaska deska drewnianaPłaska deska drewniana
2

Stake up and fit corner sticks

Point seventeen pairs of stakes, about half as thick as the sticks: ten for each side, seven for each end. Push the end stakes in beside the sticks; for the sides open holes through the outside sticks with the bodkin. Bend each stake up with the picking knife and gather them in a small hoop (Fig. 35). Cut four corner sticks as thick as the outside bottom sticks, flat-cut at the foot (Fig. 37).

Materiały do tego kroku:

Kołki wierzboweKołki wierzbowe34 17 pairs
Grubsze witki wierzboweGrubsze witki wierzbowe4 corner sticks

Potrzebne narzędzia:

PrzewlekaczPrzewlekacz
Sekator jednoręcznySekator jednoręczny
MłotekMłotek
3

Upset and rand the sides

Upset with three rods (four if there will be no foot rim), working the corner sticks in at each corner (Figs. 38-39), and add a second round. Rand with rods drawn in their lengths, each butt one stake on from the last, to about 10 in deep, keeping the sides upright and true. Leave a space between the two middle stakes of each side the full depth for the handle. Put strainers across when the middle stakes come out of the hoop, and level the weaving at about 9 in.

Materiały do tego kroku:

Witka wierzbowaWitka wierzbowa1 upsetting, randing

Potrzebne narzędzia:

MłotekMłotek
PrzewlekaczPrzewlekacz
4

Wale, border and pick

Work a wale of four rods, each behind two stakes and in front of two (Fig. 43), using eight rods, to 11 in deep. Lay the stakes down into the border and finish by cramming (Figs. 45-47). Pick every butt and top inside and out so the outside is smooth.

Materiały do tego kroku:

Witka wierzbowaWitka wierzbowa8 wale

Potrzebne narzędzia:

Sekator jednoręcznySekator jednoręczny
MłotekMłotek
5

Add the foot rim

Turn the basket over, push a rim stake in beside each stake and each corner stick, upset once round with six rods, tap down and border 'inside two and outside three' (Fig. 49).

Materiały do tego kroku:

Kołki wierzboweKołki wierzbowe1 rim stakes
Witka wierzbowaWitka wierzbowa6 upsetting

Potrzebne narzędzia:

PrzewlekaczPrzewlekacz
MłotekMłotek
6

Fit and wrap the bow handle

Bend a thick, well-soaked stick into a bow (Fig. 48), push its ends down the handle spaces to the upsetting, about 8 to 9 in above the border (some 20 in from the bottom to the underside of the bow), and shoulder it with the knee. Wrap it with four long smooth osiers, each twisted rope-fashion and lapped round the bow and through under the wale (Figs. 50-51).

Materiały do tego kroku:

Grubsze witki wierzboweGrubsze witki wierzbowe1 bow
Witka wierzbowaWitka wierzbowa4 handle wrap

Potrzebne narzędzia:

WodaWoda
PrzewlekaczPrzewlekacz
Sekator jednoręcznySekator jednoręczny

Materiały

3

Wymagane narzędzia

6

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...