Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Spring-Bow Churn: A Bow With Two Springs Keeps Its Cord Tight Round a Screw Whirl on the Crank Shaft
Buttercup

Autor

Buttercup

11. listopad 2026IE
6
0
0
0
0

Spring-Bow Churn: A Bow With Two Springs Keeps Its Cord Tight Round a Screw Whirl on the Crank Shaft

Abner Willson of Colden, New York, received US 27,181, dated 14 February 1860, for a churn worked like a bow drill. A cord from a stiff bow takes a turn round a screw whirl on the crank shaft; pushing and drawing the bow spins the crank, which lifts and drops the dasher. Two springs on the bow, one near each end, hold the cord, so it stays tight both ways and does not slip. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days, plus printing

Instrukcje

1

From bow strokes to dasher strokes

Wczytywanie notatnika Jupyter…
2

The bow and cord that turn a spindle

A bow drill's cord, wrapped round a spindle, turns it back and forth. Willson puts the same bow on a churn.
3

A crank that strokes a dasher, the year before

Austin's crank lifts and drops a dasher. Willson turns his crank with a bow instead of a handle.
4

Read US 27,181

"The effect of these two springs on an inflexible bow is to keep the cord always at a proper tension; in a flexible bow constructed as is customary, (unless the cord is very tense) when the bow is pushed, that portion of the cord between the whirl and the hither end of the bow slackens; and when the bow is drawn, that portion of the cord between the whirl and farther end of the bow slackens; this slackening which causes a slipping and a loss of power, is avoided by my peculiarly constructed bow. The threads of the whirl keep the cord from chafing."
5

Print the screw whirl D

Whirl 50 mm across and 60 long with a helical groove at 6 mm pitch for the cord, and a hub 36 mm across; bored 12.4 mm for the crank shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the dasher B

Cone dasher 160 mm across, open underneath, with a socket 20.6 mm across for the dasher rod. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Crank shaft C and dasher B

Drill a 13 mm hole through each side of the bucket, opposite each other, 300 mm above the inside floor. Cut a 12 mm stainless rod 450 mm long. Glue a 20 mm hardwood dowel 220 mm long into the dasher's socket, and drill 12.6 mm across its top end, 12 mm from the end. Starting 155 mm from one end, bend a crank 40 mm deep and 40 mm wide in the vise; slide the dasher rod's eye onto the crank pin before bending the second side. Pass the shaft through the bucket's holes with the crank inside, centred, and fit a collar on the short end. Seal round both holes outside with silicone sealant.

Materiały do tego kroku:

Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Shaft CollarShaft Collar1 sztuka
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Imadło warsztatoweImadło warsztatowe
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Miara zwijanaMiara zwijana
8

Fix the screw whirl D

Slide the whirl onto the long end of the shaft outside the bucket, hub towards the bucket, 10 mm clear of it. Drill 4 mm through the hub and shaft, and drive in a 4 mm stainless pin cut from rod, so the whirl is "firmly attached to the crank shaft".

Materiały do tego kroku:

Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka

Potrzebne narzędzia:

Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
9

Bow F with springs a and cord E

Cut a hardwood bow 700 x 50 x 30 mm, the patent's "inflexible bow", and plane and sand its underside slightly curved. Fit a dowel through one end as a handle, as in Fig. 1. Screw a spring-steel strip 120 x 16 mm by its inner end to the upper side near each end, outer ends free and reaching the bow's ends; drill a 5 mm hole through the bow under each spring's outer end and a 5 mm hole in each spring's tip. Pass a 4 mm cord up through each bow hole and tie it to the spring's tip, leaving enough slack between to take one turn round the whirl with the springs bent down a little.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Taśma ze stali sprężynowejTaśma ze stali sprężynowej2 sztuk
Wkręty do drewnaWkręty do drewna4 sztuk
SznurekSznurek1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Papier ściernyPapier ścierny
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
10

The build in 3D

FreeCAD model of this build, the bucket cut through the middle: the crank shaft with its 40 mm crank, the dasher hanging from the crank pin, the screw whirl outside, and the bow with its two springs and cord.
Plik projektowyBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket and put on its lid. Lay the cord in the whirl's groove with one turn round it, have someone steady the bucket or hold it between your feet, and push and draw the bow steadily, timing it. When the butter comes, take off the lid, lift the butter out past the dasher, tip the buttermilk out into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka8 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
12

Troubleshooting

Spring-bow churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Abner Willson** of Colden, Erie County, New York, US 27,181, 14 February 1860, "Churn". He claimed "the bow F with springs a when constructed as described, in combination with screw whirl D operating as set forth"; he did not claim the treadles G he also shows, nor the dasher, crank shaft or vessel. His vessel is a tall wooden one; ours is a food-grade bucket, and the cone dasher, its rod and our way of fixing the whirl are ours. The patent gives no sizes; every size here is ours.

Materiały

14

Wymagane narzędzia

15

Pliki projektowe

3

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...