Ubufatanye
UBUHANZI
UBWIZA N'UBUZIMA
UBUKORIKORI
UMUCO N'AMATEKA
IMYIDAGADURO
IBIDUKIKIJE
IBIRIBWA N'IBINYOBWA
UBWUBATSI BUSUBIRA INYUMA
UBUMENYI
SIPORO
IKORANABUHANGA
IBYAMBARWA
Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)
A canteen "for the camper or hiker", sent to The Boy Mechanic (1919) by J. R. Townsend of Itasca, Texas: two nickel-plated pie plates soldered rim to rim, the screw-capped neck of a metal-polish can soldered over an opening in the edge, and two wire loops for the snap hooks of a shoulder strap.
The book gives no sizes: the plates set the size.
Utangiye
About 2 hours
Amabwiriza
1
1
Read The Boy Mechanic
Read The Boy Mechanic
"Two good-quality pie plates were soldered at their edges to form a water-tight container." (J. R. Townsend, Itasca, Texas.)
2
2
Solder the plates together
Solder the plates together
Take two good-quality nickel-plated pie plates of the same size. Clean the rims, set them face to face, and solder them together all round the edge so the joint is water-tight. Use lead-free solder: this holds drinking water (our choice; the book only says solder).
Ibikoresho by'iyi ntambwe:
Isahani yo gutekeramo pie2 ibice
Umutobe wo guhuza imiyoboro udafite isasu1 igice
Umuti wo gusudira1 igiceIbikoresho bikenewe:
Icyuma cyo gusudira cy'amashanyarazi
Ikariso ry'Icyuma3
3
Cut the neck off the can
Cut the neck off the can
Take a small metal-polish can with a screw cap. As the book's drawing shows, cut off its sloping top with the threaded neck, and trim the cut edge.
Ibikoresho by'iyi ntambwe:
Ikopo ry'icyuma1 igiceIbikoresho bikenewe:
Umukasi ukomeye w'ibyumaIkariso ry'Icyuma4
4
Cut the opening and fit the neck
Cut the opening and fit the neck
Cut an opening in the edge of the canteen to suit the neck. Fit the neck carefully over it and solder it all round.
Ibikoresho by'iyi ntambwe:
Umutobe wo guhuza imiyoboro udafite isasu1 igiceUmuti wo gusudira1 igiceIbikoresho bikenewe:
Igikoresho cyo gutobora gikoreshwa n'intokiIkariso ry'IcyumaIcyuma cyo gusudira cy'amashanyarazi5
5
Solder on the strap loops
Solder on the strap loops
Bend two short pieces of wire into loops and solder one at each side of the screw cap, as loops for the snap hooks of the shoulder strap.
Ibikoresho by'iyi ntambwe:
Urusinga rw'icyuma1 igiceUmutobe wo guhuza imiyoboro udafite isasu1 igiceUmuti wo gusudira1 igiceIbikoresho bikenewe:
Ipfundo Rifite Umunwa UringaniyeIcyuma cyo gusudira cy'amashanyarazi6
6
Fit the strap and test
Fit the strap and test
Put a snap hook on each end of a shoulder strap and hook them into the loops. Fill the canteen with water, screw on the cap and check every joint for leaks (our test), then rinse it before use.
Ibikoresho by'iyi ntambwe:
Umukandara w'uruhu1 igice
Icyuma gifata gifite ispiringi2 ibiceIbikoresho bikenewe:
Amazi meza7
7
Troubleshooting
Troubleshooting
Canteen troubleshooting.
Flow
Loading...
8
8
History and honest limits
History and honest limits
From **The Boy Mechanic, Book 3**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1919 (Project Gutenberg 71856), "How to Make a Canteen", sent in by J. R. Townsend of Itasca, Texas. The book gives no sizes and names no tools; the lead-free solder, the tools, the strap material and the leak test are ours.
Ibikoresho
7- 2 ibiceUmwanya
- Umwanya
- 3 ibiceUmwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
- Umwanya
Ibikoresho bikenewe
6- Umwanya
- Umwanya
- Umwanya
Iki gishushanyo gikora
Blueprint zijyanye
Izi blueprint zisangira ubumenyi — uburyo, ibikoresho cyangwa amahame
CC0 Umurenge rusange
Iyi blueprint yasohowe munsi ya CC0. Ushobora gukoporora, guhindura, gukwirakwiza no gukoresha nta kwemererwa.
Shyigikira Umuremyi ugura ibicuruzwa binyuze muri Blueprint ye Komisiyo y'Umuremyi byashyizweho n'Abacuruzi, cyangwa kora verisiyo nshya y'iyi Blueprint ukayinjiza nk'isano muri Blueprint yawe kugira ngo musangire inyungu.