Ubufatanye
UBUHANZI
UBWIZA N'UBUZIMA
UBUKORIKORI
UMUCO N'AMATEKA
IMYIDAGADURO
IBIDUKIKIJE
IBIRIBWA N'IBINYOBWA
UBWUBATSI BUSUBIRA INYUMA
UBUMENYI
SIPORO
IKORANABUHANGA
IBYAMBARWA
English
Braked-Disk Slat-and-Wing Churn: Up Between the Slats, Down Through the Disk
Wade sent the cream round a loop: up the sides and down through the middle.
Isaac M. Wade of Clinton, Lenawee County, Michigan, received US 13,133, dated 26 June 1855, for a churn with radial wings on the foot of a vertical shaft, turned through bevel wheels by a crank; vertical slats round the inside of the tub that the wings just clear; and on the slats' shoulders a disk with a central aperture and four brakes, "flat wooden strips secured edgewise on the disk," placed tangent to the aperture and held still by a pin. The wings force the cream "upward between the slats (f) and thrown against the brakes A¹, which direct it to the aperture (g)," and the slats and brakes "prevent the cream from rotating."
This rung compares the openings, then prints the slats, the disk with its brakes, the wings, step and gears, builds the churn, and makes butter.
Hagati
About 4 hours, plus printing
Amabwiriza
1
1
Up the sides, down the middle
Up the sides, down the middle
Gupakira ikaye ya Jupyter…
2
2
Still breakers round a turning dasher, before it
Still breakers round a turning dasher, before it
The embedded blueprint turns dashers between still breakers. Wade's still slats and brakes send the cream in a loop, up the side and down through a disk.
3
3
Read US 13,133
Read US 13,133
"On the upper surface of the disk H, are attached four brakes A¹. These brakes are formed of flat wooden strips secured edgewise on the disk and extend upward nearly as high as the slats (f). The brakes are placed tangentially with the circular aperture (g), at the center of the disk H, and extend to the edge of the disk."
4
4
Print the parts
Print the parts
Print four slats with their shoulders, the disk with its aperture and four brakes, the wings, the step, the 36-tooth crown wheel, the 12-tooth pinion and the standard. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Ibikoresho by'iyi ntambwe:
Fibere ya PETG1 igiceIbikoresho bikenewe:
Imashini icapa 3D ikoresha umugozi (FDM)5
5
Print the slat
Print the slat
The slat, printed as step 4 describes.
6
6
Print the disk with its aperture and four brakes
Print the disk with its aperture and four brakes
The disk with its aperture and four brakes, printed as step 4 describes.
7
7
Print the wings
Print the wings
The wings, printed as step 4 describes.
8
8
Print the step
Print the step
The step, printed as step 4 describes.
9
9
Print the crown wheel
Print the crown wheel
The crown wheel, printed as step 4 describes.
10
10
Print the pinion
Print the pinion
The pinion, printed as step 4 describes.
11
11
Print the standard
Print the standard
The standard, printed as step 4 describes.
12
12
Tub, slats, wings and disk
Tub, slats, wings and disk
Use a straight-sided round food-grade container about 190 mm across inside and 230 mm deep. Seal the four slats upright to its wall, evenly spaced, with food-safe silicone, their shoulders inward. Stand the step in the bottom, a 10 mm square hardwood shaft in it, and slide the wings down onto the step. Drop the disk over the shaft onto the shoulders and push a short pin through its notch beside a slat, as his pin h.
Ibikoresho by'iyi ntambwe:
Ikibindi cyo kubikamo cy'urwego rw'ibiribwa1 igice
Igifunga cya silikone1 igice
Udukoni tw'ibiti bikomeye1 igice
Umurongo Uzengurutse w'Icyuma Cyoroshye1 igiceIbikoresho bikenewe:
Umucumita w'Intoki
Umucumita w'Ibyuma
Urupapuro rwo Gusya13
13
Lid, gears and crank
Lid, gears and crank
Cut the lid in half and fix one half with a hole for the shaft. Push the pinion onto the shaft's top, screw the standard to the lid half and run a short 10 mm rod through its bearing into the crown wheel so its teeth mesh the pinion; screw a dowel handle into the wheel's boss.
Ibikoresho by'iyi ntambwe:
Umurongo Uzengurutse w'Icyuma Cyoroshye1 igiceUdukoni tw'ibiti bikomeye1 igice
Uruganda rw'igiti #8 x 1"1 igice
Ibitorezo by'imashini1 igiceIbikoresho bikenewe:
Umucumita w'Ibyuma
Ikusanyirizo ry'ibitorezi
Icyuma Cyivumbura Kidafite Insinga14
14
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the tub cut away to show the wings on the step, the slats on the wall, the disk resting on their shoulders with its aperture and brakes, and the crown wheel and pinion on the half lid.
15
15
Churn the loop
Churn the loop
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres, enough to cover the disk. Crank steadily and watch the cream rise at the side and fall through the aperture; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Ibikoresho by'iyi ntambwe:
Igice cy'ibinure cy'amata2000 ml
Umunyu w'inyanja munini1 igice
Amazi1 igiceIbikoresho bikenewe:
Igipima ubushyuhe gifite uruti rusigara mu kintu
Isaha yo Guhagarika
Iminzani ya Digitale yo mu Gikoni
Ibakure rinini ryo kuvanga ry'icyuma kitagira ingese16
16
Cream that just goes round
Cream that just goes round
Braked-disk churn troubleshooting.
Flow
Loading...
17
17
History and honest limits
History and honest limits
**Isaac M. Wade** of Clinton, Lenawee County, Michigan, received US 13,133, dated 26 June 1855. The drawing marks the brakes A′ where the text has A¹. He wrote that the churn "operates well and with but a small expenditure of power even when a large quantity of cream is placed in the case"; that is his claim. He claimed the arrangement of the wings on the shaft's foot, the slats on the tub's inner side and the brakes on the disk.
**Honest limits.** A container, printed parts and a crown wheel with a spur pinion stand in for his tub and bevel wheels. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Ibikoresho
10- 1 igiceUmwanya
- Umwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
- Umwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
- 2000 mlUmwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
Ibikoresho bikenewe
10- Umwanya
- Umwanya
- Umwanya
- Umwanya
- 1 vendor sell this, none ship to you yetUmwanya
- Umwanya
Dosiye z'igishushanyo
8Iki gishushanyo gikora
Blueprint zijyanye
Izi blueprint zisangira ubumenyi — uburyo, ibikoresho cyangwa amahame
Liftable-Breaker Dasher Churn: Breakers Stand Still to Churn, Then Lift and Turn to Gather
na Emma
IBIRIBWA N'IBINYOBWA
28
0
0
0
0
0
Hydrothermal Reservoir Dasher Churn: Warm Water in the Dasher to Churn, Cold to Firm the Butter
na Karen
IBIRIBWA N'IBINYOBWA
36
0
0
0
0
0
Flaring-Tub Slat-Reactor Churn: The Cream Climbs the Flare and Is Beaten Back by Slats
na TheChef
IBIRIBWA N'IBINYOBWA
20
0
0
0
0
0
CC0 Umurenge rusange
Iyi blueprint yasohowe munsi ya CC0. Ushobora gukoporora, guhindura, gukwirakwiza no gukoresha nta kwemererwa.
Shyigikira Umuremyi ugura ibicuruzwa binyuze muri Blueprint ye Komisiyo y'Umuremyi byashyizweho n'Abacuruzi, cyangwa kora verisiyo nshya y'iyi Blueprint ukayinjiza nk'isano muri Blueprint yawe kugira ngo musangire inyungu.