التعاون
فنون
الجمال والعناية
حِرَف
الثقافة والتاريخ
ترفيه
البيئة
الطعام والمشروبات
الهندسة العكسية
العلوم
رياضة
التقنية
الأجهزة القابلة للارتداء
Potentiometer: Podolsky Roller-Contact Unit in a Moulded Casing
Ed

أنشأه

Ed

21. أكتوبر 2026FI
12
0
0
0
0

Potentiometer: Podolsky Roller-Contact Unit in a Moulded Casing

Podolsky's variable resistor (Wirt Company, US 2,060,114, 1936). The carbon strip is bent into a ring inside a moulded casing, and instead of a sliding wiper a small roller runs round it. A coil spring presses the roller out against the strip with even pressure in every position, even over slight irregularities. The patent gives no sizes; the parts are named by what they do. The picture: the patent's drawing (Figs. 8 and 9).
متوسط
2 hours

التعليمات

1

Seat the strip in the casing

Bend the resistance strip into a ring against the round inner wall of the moulded casing. A small rib across the wall stops both ends of the strip so it cannot shift; the thick part at the rib has a hole for bolting the casing to a panel. Ours: flat-nose pliers to ease the strip in.

المواد لهذه الخطوة:

Moulded Insulating CasingMoulded Insulating Casing1 قطعة
عنصر مقاومة كربونيةعنصر مقاومة كربونية1 قطعة

الأدوات المطلوبة:

كماشة مسطّحة الفكّينكماشة مسطّحة الفكّين
2

Bolt the terminals

Put two terminal bolts through the casing wall, one at each end of the strip. Under each bolt head a small contact plate rests on the coated end of the strip.

المواد لهذه الخطوة:

مسمار طرفيمسمار طرفي2 قطع
Contact PlateContact Plate2 قطع

الأدوات المطلوبة:

زرّادية طويلة الفكّينزرّادية طويلة الفكّين
3

Fit shaft, sleeve, collar and yoke

The shaft turns in a sleeve fixed in the base of the casing. A collar on the shaft rests on the outer end of the sleeve; on the inner end the shaft carries a yoke, with a spring washer between yoke and sleeve so the shaft cannot slide. Ours: pliers to seat the spring washer.

المواد لهذه الخطوة:

عمود تحكمعمود تحكم1 قطعة
Shaft SleeveShaft Sleeve1 قطعة
Shaft CollarShaft Collar1 قطعة
Shaft YokeShaft Yoke1 قطعة
Spring WasherSpring Washer1 قطعة

الأدوات المطلوبة:

زرّادية طويلة الفكّينزرّادية طويلة الفكّين
4

Fit the sprung roller

The yoke's slotted ends guide a flat stem. The roller sits in the stem's forked outer end. A washer on shoulders of the stem, pushed out by a coil spring, holds the roller on the strip with even pressure all the way round.

المواد لهذه الخطوة:

Roller StemRoller Stem1 قطعة
Contact RollerContact Roller1 قطعة
حلقة تثبيت مسطحةحلقة تثبيت مسطحة1 قطعة
Coil SpringCoil Spring1 قطعة

الأدوات المطلوبة:

زرّادية طويلة الفكّينزرّادية طويلة الفكّين

المواد

13

الأدوات المطلوبة

2

CC0 ملكية عامة

هذا المخطط مُصدر بموجب CC0. يحق لك نسخه وتعديله وتوزيعه واستخدامه لأي غرض، دون طلب إذن.

ادعم الصانع بشراء منتجات عبر مخططه حيث يكسب عمولة الصانع يحددها البائعون، أو أنشئ نسخة جديدة من هذا المخطط وضمّنه كرابط في مخططك لمشاركة الإيرادات.

النقاش

(0)

تسجيل الدخول للمشاركة في النقاش

جارٍ تحميل التعليقات...