فنون
الجمال والعناية
حِرَف
الثقافة والتاريخ
ترفيه
البيئة
الطعام والمشروبات
الهندسة العكسية
العلوم
رياضة
التقنية
الأجهزة القابلة للارتداء

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed.
Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down.
This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
متوسط
About 4 hours
التعليمات
1
1
Sheet speed from the slot
Sheet speed from the slot
جارٍ تحميل دفتر Jupyter…
2
2
Water through a brush's back before it
Water through a brush's back before it
The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3
3
Read US 840,604
Read US 840,604
"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4
4
Cut the slots
Cut the slots
On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.
المواد لهذه الخطوة:
فرشاة فرك1 قطعةالأدوات المطلوبة:
ملزمة منضدة
مثقاب لاسلكي
طقم لقم ثقب
منشار تخريم
قلم تعليم ثابت
مسطرة5
5
Taper the slots
Taper the slots
Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.
الأدوات المطلوبة:
طقم أزاميل خشب
مطرقة
قدمة رقمية 6 بوصات
سكين حِرَفية6
6
Make the manifold
Make the manifold
Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.
المواد لهذه الخطوة:
أنبوب نحاسي1 قطعة
وصلات نحاسية1 قطعةالأدوات المطلوبة:
قاطع أنابيب
مبارد (مبرد يدوي)
مفتاح ربط قابل للضبط7
7
Seat the manifold
Seat the manifold
Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.
المواد لهذه الخطوة:
لوح مطاطي1 قطعة
صفيحة ألمنيوم1 قطعة
برغي خشب #8 × 1 بوصة1 قطعةالأدوات المطلوبة:
مقصّ صفائح
طقم مفكات
سكين حِرَفية8
8
Handle, valve and drip cup
Handle, valve and drip cup
Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.
المواد لهذه الخطوة:
أنبوب نحاسي1 قطعة
محبس كروي1 قطعة
وصلات نحاسية1 قطعة
شريط PTFE لإحكام الأسنان اللولبية1 قطعة
علبة صفيح1 قطعةالأدوات المطلوبة:
قاطع أنابيب
مفتاح ربط قابل للضبط
مثقاب لاسلكي
طقم لقم ثقب9
9
The patent drawing
The patent drawing
US 840,604 drawing sheet, public domain (expired patent).

10
10
Full flow against throttled
Full flow against throttled
Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.

المواد لهذه الخطوة:
خرطوم الحديقة1 قطعة
ماء1 قطعةالأدوات المطلوبة:
إبريق قياس
ساعة إيقاف
مسطرة11
11
A sheet that sprays, sputters or leaks
A sheet that sprays, sputters or leaks
Sheet-of-water fountain brush troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised.
**Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.
المواد
12- 1 قطعةعنصر نائب
- 1 قطعةعنصر نائب
- 1 قطعةعنصر نائب
- 2 قطععنصر نائب
- 1 قطعةعنصر نائب
- 1 قطعةعنصر نائب
- 1 قطعةعنصر نائب
- 1 قطعةعنصر نائب
- عنصر نائب
- 1 قطعةعنصر نائب
- خرطوم الحديقةعمولة 10%1 قطعةعنصر نائب
- 1 قطعةعنصر نائب
الأدوات المطلوبة
17- عنصر نائب
- 1 vendor sell this, none ship to you yetعنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
المخططات ذات الصلة
هذه المخططات تشارك المعرفة مع هذا — التقنيات والمواد والمبادئ

The Tube-in-the-Back Fountain Brush: Turn the Tube and the Jets Become a Soak
بواسطة YourGrandma
ميكانيكا
34
0
0
0
0
0

The Long-Handled Fountain Brush: A Ring of Holes Wets the Bristles From the Ground
بواسطة Martin
ميكانيكا
27
0
0
0
0
0

The Hose and Its Clip: Why It Was Tight When You Fitted It
بواسطة Martin
أدوات
38
0
0
0
0
0
CC0 ملكية عامة
هذا المخطط مُصدر بموجب CC0. يحق لك نسخه وتعديله وتوزيعه واستخدامه لأي غرض، دون طلب إذن.
ادعم الصانع بشراء منتجات عبر مخططه حيث يكسب عمولة الصانع يحددها البائعون، أو أنشئ نسخة جديدة من هذا المخطط وضمّنه كرابط في مخططك لمشاركة الإيرادات.