ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Bellows Rocking-Dasher Churn: A Hand Bellows Blows Air Down a Knee Nozzle Into the Cream and Rocks a Paddle Dasher Beside It
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
12
0
0
0
0

Bellows Rocking-Dasher Churn: A Hand Bellows Blows Air Down a Knee Nozzle Into the Cream and Rocks a Paddle Dasher Beside It

Charles T. Anderson of Hyattstown, Maryland, received US 32,553, dated 18 June 1861, for a churn worked by an ordinary bellows lying on a box beside the cream. Pumping its handle drives air down a knee-shaped nozzle to holes near the bottom of the pail, under a disk on legs; at the same time two cords over a roller on the bellows rock a lever at its nose, which through a link and crank swings a paddle dasher back and forth beside the nozzle. An adjustable hole on the bellows' top sets how much air goes in; closed, the dasher churns alone. The patent gives no sizes; every size here is ours.
ขั้นสูง
About 3 days

คำแนะนำ

1

Air for the cream

กำลังโหลดสมุด Jupyter…
2

A bellows blowing air through the cream, years before

The tempered-air churn uses the bellows alone. Anderson's bellows also rocks a dasher by cords and a lever.
3

Read US 32,553

"The vessel being filled with cream, an up and down or vibratory movement is given to the upper portion of the bellows by means of the handle and a current of air thereby forced through the nozzle of the bellows into the cream through the apertures of the lower end of the nozzle. At the same time a vibrating motion is imparted to the dasher."
4

Box C, platform S, bars B and bellows A

Make a hardwood box C 520 x 360 mm and 450 high from 20 mm boards, and screw a platform S 380 x 340 x 30 mm to the ground at one end of it. Screw two hardwood bars B 40 x 20 mm across its top, 280 mm apart. Lay a hand bellows about 460 mm long on them, its nozzle toward the platform, and screw its bottom board to the bars. Bore a 30 mm hole in its top board as the aperture b and screw over it a hardwood slide in guides, to open it wide, part way or shut. Bore a 40 mm hole in the bottom board near its nose and glue a leather flap over it inside, hinged at one edge, as the valve that lets air in as the bellows opens. Screw two hardwood cross pieces D 200 x 30 mm on the top board and a hardwood handle E 400 mm long to them, reaching back.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง4 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้40 ชิ้น
สูบลม (เครื่องเป่าลมมือ)สูบลม (เครื่องเป่าลมมือ)1 ชิ้น
หนังฟอกหนังฟอก1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
แคลมป์แบบบาร์แคลมป์แบบบาร์
ชุดไขควงชุดไขควง
ตลับเมตรตลับเมตร
5

Print the knee elbow

The elbow joining the nozzle's two tubes: two 22.4 mm sockets at right angles round a 17 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
6

Nozzle G, disk I and the pail H

Cut a 22 mm stainless tube into a short end f 300 mm long and a long end 460 mm long and join them at right angles in the printed elbow with food-safe silicone, as the knee nozzle G; drill six 7 mm holes round the long end 25 mm above its foot. Fit the short end into the bellows' nozzle, sealed with leather. Cut an HDPE disk I 180 mm across, bore it 22.6 mm 80 mm from its centre for the tube, four 24 mm apertures h round its centre, and a socket boss at its centre; screw three hardwood legs g 60 mm long under it. Slide it on the tube so the tube's foot and the legs stand on the floor of a 20-litre food-grade pail H set on the platform. Cover the pail with butter muslin.

วัสดุสำหรับขั้นตอนนี้:

ท่อสเตนเลสท่อสเตนเลส1 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น
ซิลิโคนยาแนวซิลิโคนยาแนว1 ชิ้น
หนังฟอกหนังฟอก1 ชิ้น
แผ่น HDPEแผ่น HDPE1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
สกรูไม้สกรูไม้3 ชิ้น
ถังขนาด 20 ลิตรถังขนาด 20 ลิตร1 ชิ้น
ผ้าขาวบางกรองเนยแข็งผ้าขาวบางกรองเนยแข็ง1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
เข็มทิศเข็มทิศ
7

Staff J, dasher M, yoke, crank K and link L

Turn a hardwood staff J 20 mm across and 375 mm long, its foot to fit the disk's socket. Screw a hardwood paddle M 120 x 200 x 12 mm across it, its foot 25 mm above the disk. Fix a yoke of mild steel flat bar to the tube 340 mm above the pail's floor, with a ring round the staff's top. Pin a crank K of flat bar, 60 mm throw, on the staff's top, and join it with a flat bar link L to one end of the lever F.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
สกรูไม้สกรูไม้4 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด2 ชิ้น
สลักผ่าสลักผ่า2 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงไม้เครื่องกลึงไม้
เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดไขควงชุดไขควง
8

Print the forked bracket O

The forked bracket on the bellows' top board: 160 mm long, a 40 x 34 mm fork to slide on the post and a 30 x 24 slot for the roller P. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
9

Lever F, post N, bracket O, roller P and cords Q, R

Cut a hardwood lever F 300 x 30 x 15 mm and pivot it at its middle on an M10 bolt e upright in the bellows' nose block, with a wing nut. Screw a pedestal block to the box's back end and stand a hardwood post N 30 mm square, 380 tall, in it behind the bellows. Screw the bracket O to the top board's back end so its fork slides on the post, and pin a hardwood roller P 18 mm across in its slot. Tie a cord Q from the post's top, under the roller, to one end of the lever, and a cord R from the pedestal, over the roller, to the other end, both just taut with the bellows half open.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด1 ชิ้น
น็อตปีกผีเสื้อน็อตปีกผีเสื้อ1 ชิ้น
แหวนรองแบนแหวนรองแบน2 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
เชือกเส้นเล็กเชือกเส้นเล็ก1 ชิ้น
สกรูไม้สกรูไม้8 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ประแจเลื่อนประแจเลื่อน
ชุดไขควงชุดไขควง
ตลับเมตรตลับเมตร
10

The build in 3D

FreeCAD model of this build, the pail cut open: the box and platform, the bellows with its slide, cross pieces and handle, the knee nozzle down to the holed foot under the disk on its legs, the staff with its paddle and yoke, the lever on its bolt, the link, and the post with the forked bracket, roller and cords.
ไฟล์แบบBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the pail and cover it with the muslin. Work the handle up and down steadily, timing it: the bellows blows air out under the cream and the paddle rocks. Open or close the slide on the bellows' top to give more or less air. When the butter comes, unhook the link from the crank, draw the nozzle out of the bellows and lift the pail away; turn the disk on the tube until the staff's foot clears it and lift the dasher out. Take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด8 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
12

Troubleshooting

Bellows churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Charles T. Anderson** of Hyattstown, Montgomery County, Maryland, US 32,553, 18 June 1861, "Churn". He claimed the pivoted reciprocating dasher M with the bellows A and vertical nozzle G, and the nozzle G, detachable dasher M and eccentrically pivoted disk I together. His bellows was "of ordinary construction"; ours is a bought or made hand bellows with the patent's top aperture, valve and nozzle added. His vessel could be a firkin, pail, can or box. The patent gives no sizes; every size here is ours.

วัสดุ

21

เครื่องมือที่จำเป็น

19

ไฟล์ออกแบบ

3

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...