ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Hollow-Staff Plunger Churn: A Plunger in a Perforated Inner Cylinder Draws Air Down Its Staff on the Up Stroke
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
13
0
0
0
0

Hollow-Staff Plunger Churn: A Plunger in a Perforated Inner Cylinder Draws Air Down Its Staff on the Up Stroke

William Hamilton of St. Catharine, Missouri, received US 31,715, dated 19 March 1861, for a plunge churn with a perforated cylinder standing inside the tub. A bevelled plunger fits the cylinder like a piston on a hollow staff with a valve at its foot. Pulled up fast, it leaves a partial void below that the milk cannot fill quickly through the holes, so the valve opens and air rushes down the staff; pushed down, the valve shuts and the air is driven through the milk, which is thrown in and out through the holes against the tub's wall. The patent gives no sizes; every size here is ours.
เริ่มต้น
About 1 day

คำแนะนำ

1

Why air is drawn in on the up stroke

กำลังโหลดสมุด Jupyter…
2

A valve in a close-fitting dash, six weeks before

Stevens's valve lets cream through his dash. Hamilton's lets air down a hollow staff, and his plunger works in a perforated cylinder.
3

Read US 31,715

"On the descent of the dasher said valve closes, and such admitted fresh air is forcibly made to permeate the body of milk and to abruptly counteract its tendency to fill the partial void below the dasher."
4

Tub A and inner cylinder B

Use a 20-litre food-grade bucket as the tub A and cut a 12 mm HDPE lid to it with a 24 mm hole in the middle. Cut a strip of 1 mm stainless sheet 320 mm wide and 645 long, drill twelve rows of 6 mm holes along it 25 mm apart, 36 to a row, the rows staggered, and roll it into a cylinder B 200 mm across, riveting the lap.

วัสดุสำหรับขั้นตอนนี้:

ถังขนาด 20 ลิตรถังขนาด 20 ลิตร1 ชิ้น
แผ่น HDPEแผ่น HDPE1 ชิ้น
แผ่นสเตนเลสแผ่นสเตนเลส1 ชิ้น
หมุดย้ำแบบดึงหมุดย้ำแบบดึง8 ชิ้น

เครื่องมือที่ต้องใช้:

เข็มทิศเข็มทิศ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดปืนย้ำหมุดชุดปืนย้ำหมุด
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
5

Print the feet (three)

A foot that holds the cylinder 15 mm off the floor: 28 mm across, 25 high, with a slotted socket for the cylinder's edge. Print three. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
6

Print the plunger C

The plunger: 196 mm across, bevelled on both faces from 120 mm at its hub to its 6 mm rim, with a hub 32 mm across and a 22.2 mm bore for the staff. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
7

Print the valve seat

The seat glued to the staff's foot under the plunger: 32 mm across, 6 thick, 19 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
8

Staff D, plunger C, valve b and handle

Cut a 22 mm stainless tube with a 19 mm bore 600 mm long as the hollow staff D. Glue the plunger on it 25 mm above its foot with silicone and pin it, and glue the valve seat to its foot. Cut a 30 mm disc of 2 mm natural rubber sheet as the valve b and fix it under the seat by one edge with a small stainless pin, so it hangs open when pulled down and lies shut when pushed up. Turn a hardwood T handle 240 mm long and fit it on the staff's top, leaving the tube's mouth open.

วัสดุสำหรับขั้นตอนนี้:

ท่อสเตนเลสท่อสเตนเลส1 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น
ซิลิโคนยาแนวซิลิโคนยาแนว1 ชิ้น
สลักผ่าสลักผ่า1 ชิ้น
แผ่นยางธรรมชาติแผ่นยางธรรมชาติ1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เครื่องกลึงไม้เครื่องกลึงไม้
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
9

The build in 3D

FreeCAD model of this build, cut open: the bucket, the perforated inner cylinder on its feet, the bevelled plunger on its hollow staff with the valve seat below, the lid and the T handle.
ไฟล์แบบBLENDCC0 - Free
10

Churn and gather

Stand the cylinder on its feet in the bucket and pour about 12 litres of heavy cream at about 15 °C, checked with the thermometer, into it; it runs out through the holes to fill the bucket. Put the plunger in, the lid over the staff, and work it up and down briskly, timing it. When the butter comes, lift out the plunger and the cylinder, then give the cream a few gentle strokes with the plunger to gather the butter. Take it out, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด12 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
11

Troubleshooting

Plunger churn troubleshooting.

Flow

Loading...
12

History and honest limits

**William Hamilton** of St. Catharine, Linn County, Missouri, US 31,715, 19 March 1861, "Churn". He claimed, in a plunger churn with a hollow staff and air valve and the dasher's cylinder inside a tub with a milk space between, "a reticulated dasher cylinder or inner case so perforated as that a constant communication is established through the meshes of the inner cylinder between the inner and outer cylinders both above and below the dasher". He wrote that three to five minutes suffice and good cream makes butter in two; we have not tested that. He left the valve's form open ("any suitable valve"); ours is a rubber flap. The patent gives no sizes; every size here is ours.

วัสดุ

16

เครื่องมือที่จำเป็น

16

ไฟล์ออกแบบ

4

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...