ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Bathroom Scale: Four Flat Load Cells Between Two Plates (Angel, 1991)
A floor scale only as thick as two plates. Four flat load cells sit in the corners between a base and a top plate; their strain gauges are wired into one bridge, so the signal is the sum of the four loads wherever you stand.
Result: a low digital bathroom scale reading in pounds or kilograms. The patent gives under 0.05 % non-linearity, hysteresis and non-repeatability, and under 0.1 % error from off-centre loads; its feet let it stand on thick carpet.
Source: S. Angel, US Patent 4,993,506 (1991). Unknown: the plate material and size, the maximum load, and the circuit. Ours: ebonite for the hard rubber, epoxy, the amplifier and display parts. Picture: patent drawing (Fig. 5).
ขั้นสูง
2 days
คำแนะนำ
1
1
Mount the four load cells
Mount the four load cells
Put one load cell in each corner of the rigid base plate. Screw each one down to small flat raised pads on the plate. Place the pads away from the edge of the cell's beam, so that fixing the cell does not change its sensitivity. Under each cell, tap two holes through the base for the overload screws. Not given: the plate material and size.
วัสดุสำหรับขั้นตอนนี้:
โหลดเซลล์4 ชิ้น
แผ่นฐานและแผ่นบนของเครื่องชั่ง1 base and top plate
สกรูเกลียวมิล8 cell screwsเครื่องมือที่ต้องใช้:
ชุดต๊าปและดายทำเกลียว
ชุดไขควง
ขนาดที่ไม่ทราบ2
2
Wire one bridge and the readout
Wire one bridge and the readout
Each cell's two gauges are half a Wheatstone bridge. Join the four halves into one full bridge, one half at each corner, so the bridge gives a signal in step with the sum of the four loads. The signal is amplified, turned into numbers by an analog-to-digital converter, worked into pounds or kilograms and shown on a display. Put the electronics and batteries in the space between the plates. Not given: the circuit. Ours: an op-amp and a segment LCD.
วัสดุสำหรับขั้นตอนนี้:
ไอซีออปแอมป์1 amplifier
ตัวแปลงสัญญาณแอนะล็อกเป็นดิจิทัล1 ชิ้น
จอแอลซีดีแบบเซกเมนต์1 ชิ้น
แบตเตอรี่1 as the circuit needs
สายไฟต่อวงจร1 as needed
ลวดตะกั่วบัดกรี1 a littleเครื่องมือที่ต้องใช้:
หัวแร้งบัดกรี3
3
Fit the top plate on hard rubber pads
Fit the top plate on hard rubber pads
Glue four flat round pads of a rigid but slightly yielding material, such as hard rubber, under the top plate. Give each pad small round studs that snap into the two load holes of its cell, so the weight goes in at the centres of those holes. The pads soften impacts when something is dropped on the scale and take up sideways forces as the top plate bends. The snaps let the top plate be pulled off for repairs. Ours: ebonite and epoxy.
วัสดุสำหรับขั้นตอนนี้:
แท่งอีโบไนต์1 four pads
อีพ็อกซีสองส่วน1 a littleเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก4
4
Fit the feet
Fit the feet
Under the base, below each cell, fix a shallow foot of flexible material such as hard rubber, rounded underneath. Put its lowest point exactly below the centre of the cell's beam: the floor then pushes up at the beam's centre without bending it, and the scale works on thick carpet or uneven floors. Ours: ebonite.
วัสดุสำหรับขั้นตอนนี้:
แท่งอีโบไนต์1 four feet
อีพ็อกซีสองส่วน1 a littleเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก5
5
Set the overload stops
Set the overload stops
Load the scale to its maximum capacity. Turn the short screws in from below until they just touch the arms of each cell's loading element, then lock them with adhesive. Any heavier load now rests on the screws instead of bending the cells further. Not given: the maximum capacity. Ours: calibration weights and epoxy.
วัสดุสำหรับขั้นตอนนี้:
สกรูเกลียวมิล8 overload screws
อีพ็อกซีสองส่วน1 a littleเครื่องมือที่ต้องใช้:
ชุดตุ้มน้ำหนักสอบเทียบ
ชุดไขควงวัสดุ
11- 4 ชิ้นตัวยึดตำแหน่ง
- 1 base and top plateตัวยึดตำแหน่ง
- 8 overload screwsตัวยึดตำแหน่ง
- 1 amplifierตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 as the circuit needsตัวยึดตำแหน่ง
- 1 as neededตัวยึดตำแหน่ง
- 1 a littleตัวยึดตำแหน่ง
- 1 four feetตัวยึดตำแหน่ง
- 3 a littleตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
6- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 2 vendors sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
วัสดุจากพิมพ์เขียวที่เชื่อมต่อ
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้



