การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Bench Glassblowing Torch: Brass Gas Blowpipe with a Glass Air Jet (Shenstone, 1916)
A glassblower's gas blowpipe you can make yourself: a brass tube with a side tube for gas, and a glass air jet down its middle fed from a foot-blower. A fine jet gives the small pointed flame for joints, and a wider jet the big brush flame for heating large tubes. It is pegged into a wooden block on a sheet-iron-covered bench, with taps for gas and air at the bench edge.
Result: a bench blowpipe for working glass tube. Make two: one about 11 mm bore for small work, one 15 to 17 mm for large.
Source: W. A. Shenstone, The Methods of Glass-Blowing (1916), pp. 3-9. Unknown: the brazing metal and the tap type. Picture: Fig. 1 of the book.
ระดับกลาง
Unknown
คำแนะนำ
1
1
Braze the gas inlet
Braze the gas inlet
Take a brass tube for the body: about 11 mm bore for the small blowpipe, 15 to 17 mm for the large one. Braze a side tube for the gas onto it 10 to 12 cm from the back end, according to the tube's size. Fix a spike to it for mounting. Ours: borax as the flux. Not given: the brazing metal.
วัสดุสำหรับขั้นตอนนี้:
ท่อทองเหลือง1 body and side tube
โลหะที่ไม่ทราบ1 brazing metal and spike
ผงบอแรกซ์1 brazing fluxเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
เตาตีเหล็ก2
2
Fit the glass air jet
Fit the glass air jet
Fit a glass tube down the middle of the brass tube, held by a cork at the back end, its tip near the mouth. For the small pointed flame, draw the tip down to the size of a large knitting needle. For a large flame rich in air, the tip may be nearly half the bore of the brass tube. Make several air tubes of different sizes for each blowpipe.
วัสดุสำหรับขั้นตอนนี้:
หลอดแก้ว3 air jets of several sizes
จุกไม้ก๊อก1 jet corkเครื่องมือที่ต้องใช้:
ตะเกียงบุนเซน3
3
Set up the bench
Set up the bench
Cover the bench round the blowpipe with sheet iron. Drill several holes in a block of wood so the spike can be set at different positions. Fix two taps near the bench edge, one for gas and one for air. Connect them by flexible tubes to the supplies on one side and to the blowpipe's gas inlet and air jet on the other. Ours: mild steel sheet, rubber tubing. Not given: the tap type.
วัสดุสำหรับขั้นตอนนี้:
แผ่นเหล็กกล้าละมุน1 bench cover
ท่อนไม้เนื้อแข็ง1 mounting block
วาล์วที่ไม่ทราบ2 gas and air taps
ท่อยาง1 flexible tubesเครื่องมือที่ต้องใช้:
สว่านแท่น4
4
Light it and blow
Light it and blow
Light the gas at the mouth and work a foot-blower to drive air through the glass jet into the burning gas. Little air and a small jet give the pointed flame; plenty of gas and a strong blast give the large, non-luminous brush flame.
เครื่องมือที่ต้องใช้:
สูบลม (เครื่องเป่าลมมือ)วัสดุ
9- 1 body and side tubeตัวยึดตำแหน่ง
- 1 brazing metal and spikeตัวยึดตำแหน่ง
- 1 brazing fluxตัวยึดตำแหน่ง
- 3 air jets of several sizesตัวยึดตำแหน่ง
- 1 jet corkตัวยึดตำแหน่ง
- 1 bench coverตัวยึดตำแหน่ง
- 1 mounting blockตัวยึดตำแหน่ง
- 2 gas and air tapsตัวยึดตำแหน่ง
- 1 flexible tubesตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
5- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
วัสดุจากพิมพ์เขียวที่เชื่อมต่อ

การระบุ 10%
Venetian Borax: Refining Tincal with Lime
โดย Charlie
อนินทรีย์
23
0
0
0
1
0

การระบุ 10%
Natural Rubber Tubing, Bands and Sheet: Sulfur-Cured with Heat
โดย Mary
เคมี
16
0
0
0
2
0

การระบุ 10%
Oak Boards and Blocks, Milled and Air-Dried
โดย Woody
งานไม้
46
0
0
0
3
0

การระบุ 10%
Building a Box Bellows — The Breath That Makes Metal Obey Fire
โดย Emma
งานไม้
109
0
0
0
8
0
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
