ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Bevel Pinion: 12 Teeth, 8 Pitch, for a 24-Tooth Gear (Brown & Sharpe 1911)
Forge

สร้างโดย

Forge

27. ตุลาคม 2026NO
17
0
0
0
0

Bevel Pinion: 12 Teeth, 8 Pitch, for a 24-Tooth Gear (Brown & Sharpe 1911)

Brown & Sharpe's own worked example: the small gear of a 12 and 24 tooth bevel pair, 8 pitch, shafts at right angles, cut with the No. 8 cutter they send to anyone who orders one for this pinion. The method is the same as for mitre gears: set off centre, cut each side, file the small ends. Source: Brown & Sharpe, Practical Treatise on Gearing (1911), Fig. 23 example, Part I ch. IX–X, Part II ch. III and the set-over table p. 58. The blank sizes are our arithmetic with their rules; the steel and bore are ours. Picture: their Fig. 23.
ขั้นสูง
1 day

คำแนะนำ

1

Work out and turn the blank

Pitch diameter 12 ÷ 8 = 1.500 in. Angle of edge 26° 34′ and angle of face 59° 11′ (Brown & Sharpe's figures for every 12 and 24 tooth pair). Diameter increment = cos 26° 34′ × 0.250 = 0.224 in, so turn the steel blank to 1.72 in outside diameter. Face ½ in long. Try both angles with a protractor against the end of the hub.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กกล้าละมุนแท่งเหล็กกล้าละมุน1 length for one blank

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
มีดกลึงมีดกลึง
ไม้โปรแทรกเตอร์ไม้โปรแทรกเตอร์
ไมโครมิเตอร์ไมโครมิเตอร์
2

Choose the cutter

Twice the back cone radius × 8 comes to about 13, so a No. 8, 8-pitch bevel gear cutter. Measure its thickness Tc at the pitch line, 0.145 in from its tip.

เครื่องมือที่ต้องใช้:

ดอกกัดเฟืองดอกจอกดอกกัดเฟืองดอกจอก
เวอร์เนียร์วัดฟันเฟืองเวอร์เนียร์วัดฟันเฟือง
3

Set the head at 22° 18′

Apex distance = sec 26° 34′ × 1.5 = 1.677 in. Angle increment: tan = sin 26° 34′ ÷ 6, giving 4° 16′. Set the dividing head to the cutting angle 26° 34′ − 4° 16′ = 22° 18′ and index 12 spaces. Depth at the large end 0.270 in.

เครื่องมือที่ต้องใช้:

เครื่องกัดเครื่องกัด
หัวแบ่งหัวแบ่ง
ดอกกัดเฟืองดอกจอกดอกกัดเฟืองดอกจอก
4

Set over and cut one side

Apex distance ÷ face = 3.35; we take the nearest column, 3¼, where a No. 8 cutter has the factor .286. Set-over = Tc ÷ 2 − .286 ÷ 8 = Tc ÷ 2 − 0.036 in. Set off centre by that amount, take up backlash, and cut round all 12 spaces.

เครื่องมือที่ต้องใช้:

เครื่องกัดเครื่องกัด
หัวแบ่งหัวแบ่ง
ดอกกัดเฟืองดอกจอกดอกกัดเฟืองดอกจอก
5

Set over the other way and trim

Set over the same amount the other side, line the cutter up with the space at the small end, take a trial cut, and rotate toward the cutter until the tooth is 0.196 in thick at the large end and 0.138 in at the small end. Check with the gear tooth vernier, then cut round.

เครื่องมือที่ต้องใช้:

เครื่องกัดเครื่องกัด
หัวแบ่งหัวแบ่ง
ดอกกัดเฟืองดอกจอกดอกกัดเฟืองดอกจอก
เวอร์เนียร์วัดฟันเฟืองเวอร์เนียร์วัดฟันเฟือง
6

File the small ends

File the teeth rounder at the small ends, where the cutter could not, without filing them thinner at the pitch line. The cutting angle is under 30°, so the spaces may come out narrower at the face than the cutter suggests; Brown & Sharpe's own shop used a No. 6 cutter here instead.

เครื่องมือที่ต้องใช้:

ตะไบเนื้อละเอียดตะไบเนื้อละเอียด

วัสดุ

1

เครื่องมือที่จำเป็น

9

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...