การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Coasting Toboggan: Four Steamed Hardwood Boards Bent Over a Log Form (Boy Mechanic, 1919)
Woody

สร้างโดย

Woody

13. พฤศจิกายน 2026NO
12
0
0
0
0

Coasting Toboggan: Four Steamed Hardwood Boards Bent Over a Log Form (Boy Mechanic, 1919)

A. M. Parker's toboggan from The Boy Mechanic, Book 3 (1919), 7-1/2 ft long and 16 in wide: four 5/16 in hardwood boards steamed at one end and bent round a 12 in log on a simple form, held by notched cross cleats, the curl riveted and wired, and a rope run along the sides.
ระดับกลาง
About 1 week (four days drying)

คำแนะนำ

1

His mill bill in centimetres

กำลังโหลดสมุด Jupyter…
2

Read The Boy Mechanic, Book 3

"Essentials of a good toboggan, whether for coasting or use in transportation, are strength and lightness." Woods in order of merit: hickory, birch and oak (not quarter-sawed).
3

Prepare the boards and cleats

Choose four 5/16 by 4 in by 10 ft boards straight in grain and free from knots. Plane the running side and bevel the edges so that, together, they form a wide V joint half the depth of the boards. Notch the seven 1 by 1 in cross cleats on one side, 1 in from each end, for the side ropes.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง4 ชิ้น

เครื่องมือที่ต้องใช้:

กบไสไม้กบไสไม้
เลื่อยมือเลื่อยมือ
สิ่วสิ่ว
ดินสอดินสอ
ตลับเมตรตลับเมตร
4

Build the bending form

Bore a gimlet hole through the centre of each 1 by 2 by 18 in piece and two more 4-1/4 in each side of it. Nail one 6 ft common board to each end of the 12 in by 18 in log block so their ends run parallel. With 3 in nails fix one bored cleat to the block between them, held out 1/2 in by a temporary spacer.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้สนแผ่นไม้สน2 ชิ้น
ตะปูตะปู1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สว่านมือสว่านมือ
ค้อนค้อน
5

Steam and bend

Steam about 3 ft of the board ends, or boil them in a tank. Clamp or nail the dry ends together edge to edge between two of the 1 by 2 in pieces, about 1/4 in apart. Push the steamed ends under the cleat on the block (its nails slip between the boards), bear down and nail on another bored cleat as far as the floor allows. Turn it over and bend the boards round the block, nailing on more cleats, until the clamped end lies between the 6 ft boards; hold it with a piece nailed across. The closer the cleats, the less risk of splitting.

วัสดุสำหรับขั้นตอนนี้:

ตะปูตะปู1 ชิ้น

เครื่องมือที่ต้องใช้:

หม้อใบใหญ่หม้อใบใหญ่
ค้อนค้อน
แคลมป์แบบบาร์แคลมป์แบบบาร์
6

Fit the cleats and finish

Dry at least four days on the form. Clamp the two 1/2 by 1 in pieces on each side of the bow ends, drill through and rivet them. Rivet a 1 by 1 in crossbar inside the bow at the extreme front and another under the end of the curl, and wire them together to hold the bend. Put the tail crossbar not nearer than 2-1/2 in from the board ends and space the rest evenly, notched side down. Trim, scrape and sandpaper the bottom, finish with oil, and run a 3/8 in rope through the notches under the cleat ends.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
หมุดย้ำเหล็กกล้าหมุดย้ำเหล็กกล้า1 ชิ้น
ลวดเหล็กดัดลวดเหล็กดัด1 ชิ้น
น้ำมันลินสีดน้ำมันลินสีด1 ชิ้น
กระดาษทรายกระดาษทราย1 ชิ้น
เชือกฝ้ายตีเกลียวเชือกฝ้ายตีเกลียว1 ชิ้น

เครื่องมือที่ต้องใช้:

สว่านมือสว่านมือ
ค้อนค้อน
เลื่อยมือเลื่อยมือ
ที่ขูดเหล็กที่ขูดเหล็ก
คีมปากแบนคีมปากแบน
7

Troubleshooting

Toboggan troubleshooting.

Flow

Loading...
8

History and honest limits

From "Making a Coasting Toboggan" by A. M. Parker, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 11-13). The tools and metric figures are ours.

วัสดุ

8

เครื่องมือที่จำเป็น

11
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • 1 vendor sell this, none ship to you yet
    ตัวยึดตำแหน่ง
  • 1 vendor sell this, none ship to you yet
    ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...