การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Five-Foot Bait-Casting Rod: Hand-Tapered Dagame Stick, Cork Grasps and Agate Guides (Boy Mechanic, 1915)
Stillman Taylor's first rod for a beginner, from The Boy Mechanic, Book 2 (1915): a one-piece 5 ft bait-casting rod planed by hand from a 5/8 in square stick of dagame to his calipered taper (1/2 in at the grasp to 1/8 in at the tip), with a double cork grasp around the reel seat, two agate guides and an agate tip, whipped in silk and varnished. He made it with "a saw, plane, jackknife, file, and sandpaper".
ระดับกลาง
About 2 weeks (glue and varnish drying)
คำแนะนำ
1
1
Fig. 5: the taper, station by station
Fig. 5: the taper, station by station
กำลังโหลดสมุด Jupyter…
2
2
Read The Boy Mechanic, Book 2
Read The Boy Mechanic, Book 2
"The short one-piece bait-casting rod with but one ferrule is the easiest rod to make." His materials: 1 dagame or greenheart stick, 5 ft long and 5/8 in square; 1 reel seat with straight hood, 3/4 in; 1 butt cap, 1 in; 1 taper, small end 15/32 in; 1 offset agate top, 3/32 in, and 2 narrow agate guides, 1/2 in, all in German silver; 2 doz. corks, 1-1/4 by 1-1/8 in; two 50 yd spools of silk, red and green, 00 size.
3
3
Make the gauge and grooved board
Make the gauge and grooved board
On a strip of paper draw the rod full length: a 1/2 in line for the butt, a centre line 60 in long, a 1/8 in line at the tip, and join the ends. From 12 in, mark a crossline every 6 in and write his diameters on them (see the notebook). File nine slots in a thin strip of brass to these diameters as a gauge. Plane a groove, gradually shallower toward one end, in a 5 ft tongue-and-groove pine board about 1 in thick, and nail it to the bench edge, groove up.
วัสดุสำหรับขั้นตอนนี้:
แผ่นทองเหลือง1 ชิ้น
แผ่นไม้สน1 ชิ้น
ตะปู1 ชิ้นเครื่องมือที่ต้องใช้:
กระดาษห่อของสีน้ำตาล
ดินสอ
ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะ
เวอร์เนียคาลิเปอร์
กบไสไม้
ค้อน
ตลับเมตร4
4
Plane the stick square and tapered
Plane the stick square and tapered
Plane along each side and from both ends of a 5/8 in square dagame strip to find the grain. Drill two holes about 1/4 in from the butt end and hook them over a brad in the bench corner, so you plane with the grain. Plane it straight and true to 1/2 in square, evenly from all sides, ignoring kinks. Knife-mark the hand grasp 12 in from the butt (11 in for a single grasp). Then plane an even taper from butt to tip, checking with caliper and gauge at every 6 in mark and planing the thick spots lightly. Bend the tip on the floor: if it stays bent, the wood needs a few weeks' seasoning in a warm place.
วัสดุสำหรับขั้นตอนนี้:
ไม้ดากาเม1 ชิ้น
ตะปู1 ชิ้นเครื่องมือที่ต้องใช้:
กบไสไม้
กบมือเล็ก
หินลับมีด
สว่านมือ
เวอร์เนียคาลิเปอร์
มีดคัตเตอร์งานประดิษฐ์
ค้อน5
5
Round the rod
Round the rod
Lay the rod in the grooved board, a corner up, and take each corner off with a finely set small plane to make it eight-sided, calipering every 6 in mark and keeping the eight sides even, until it is almost round and tapers evenly from the grasp mark to the tip. File grooves across the edge of a cabinetmaker's steel scraper with a round file, sharpen them, and scrape the rod perfectly round; sandpaper it smooth. Tie on the tip and guides and string the reel on to try a few casts, then smooth it with No. 0 sandpaper.
วัสดุสำหรับขั้นตอนนี้:
กระดาษทราย1 ชิ้นเครื่องมือที่ต้องใช้:
กบมือเล็ก
ที่ขูดเหล็ก
ตะไบ (ตะไบมือ)
เวอร์เนียคาลิเปอร์6
6
Build the lower grasp and reel-seat sleeve
Build the lower grasp and reel-seat sleeve
Cut a hole in the corks with a sharpened tube turned like a wad cutter. Cut the butt off square about 1 in from the end, to remove the holes. Glue on a cork with hot glue, then cork after cork, about 10, for a grasp a trifle over 5 in long. For the reel-seat sleeve, bore a 15/32 in hole through white pine about 3/4 in thick and 5 in long, plane the outside to slip inside the reel seat, taper one end to match it, and make it about 1/4 in shorter than the reel seat. Glue it down on top of the last cork and leave the glue a day or two.
วัสดุสำหรับขั้นตอนนี้:
แหวนไม้ก๊อก10 ชิ้น
กาวสัตว์1 ชิ้น
แผ่นไม้สน1 ชิ้นเครื่องมือที่ต้องใช้:
ท่อทองเหลือง
ตะไบ (ตะไบมือ)
เลื่อยมือ
สว่านมือ
กบมือเล็ก7
7
Fit the butt cap and reel seat
Fit the butt cap and reel seat
Trim the grasp to about 1-1/16 in diameter (1-1/4 in corks need little trimming), leaving the top cork as a shoulder, and fit the lower corks to the butt cap's taper. Heat the cap moderately, rub melted ferrule cement inside and force it on; when hard, drive a small brass pin or brad through and file it flush. Cut the 4-1/2 in reel seat down to 3-7/8 in and fit it with the hood at the lower end, worked into the cork for a tight joint. Cement the sleeve, push the reel seat home and drive a small pin through the hood into the wood a short way only, not through the rod.
วัสดุสำหรับขั้นตอนนี้:
ฝาปิดท้ายคันเบ็ด1 ชิ้น
ที่ยึดรอก1 ชิ้น
กาวติดปลอกต่อคัน1 ชิ้นเครื่องมือที่ต้องใช้:
มีดคัตเตอร์งานประดิษฐ์
ตะไบ (ตะไบมือ)
หัวพ่นไฟโพรเพน
ค้อน8
8
Build the upper grasp and finish the wood
Build the upper grasp and finish the wood
Cement corks above the reel seat, the first pressed against the seat and turned so the metal enters it, then shape them into a smooth swelled grasp and cement on the winding check. Sand the rod, wet it to raise the grain, and sand again with old paper; for a finer polish rub with pumice and oil and an oiled rag. File the tip to fit the agate top, smear on melted ferrule cement and push the top home. Rub the wood over with a cloth wet with varnish to fill the pores, and wipe off the surplus.
วัสดุสำหรับขั้นตอนนี้:
แหวนไม้ก๊อก6 ชิ้น
กาวสัตว์1 ชิ้น
แหวนปิดรอยต่อด้าม1 ชิ้น
ไกด์ปลายคัน1 ชิ้น
กาวติดปลอกต่อคัน1 ชิ้น
กระดาษทราย1 ชิ้น
วานิชรถม้า1 ชิ้นเครื่องมือที่ต้องใช้:
มีดคัตเตอร์งานประดิษฐ์
ตะไบ (ตะไบมือ)
หัวพ่นไฟโพรเพน9
9
Whip on the guides
Whip on the guides
Place the first guide 19-1/2 in from the metal taper above the upper grasp and the second 15-1/2 in further on; round the sharp edges of their bases with a fine file and hold them with a few turns of common thread. Whip with 00 silk using the invisible knot: tuck the end under the first coil, wind tightly by turning the rod, lay a waxed loop of silk about 4 in long under the last turns, wind about 1/8 in beyond the pointed flange, cut the silk and pull its end back under with the loop. About a dozen turns make a winding; edgings of three or four turns go on after, in red with green or yellow.
วัสดุสำหรับขั้นตอนนี้:
ไกด์คันเบ็ด2 ชิ้น
ไหมพันคันเบ็ด1 ชิ้น
ด้ายลินิน1 ชิ้น
ขี้ผึ้ง1 ชิ้นเครื่องมือที่ต้องใช้:
ตะไบ (ตะไบมือ)
มีดคัตเตอร์งานประดิษฐ์10
10
Shellac and varnish
Shellac and varnish
Clip any fuzzy ends and give the silk two light coats of white shellac dissolved in grain alcohol, warmed and laid on with a small camel's-hair brush; let it dry a couple of days. Warm the coach varnish in a pot of hot water for five minutes and brush it on evenly with a brush about 1/2 in wide, in a warm place (about 75 deg F). Hang the rod by the tip in a dust-free room; allow three days between coats; two coats protect it, three give complete protection.
วัสดุสำหรับขั้นตอนนี้:
น้ำมันเคลือบเชลแล็ก1 ชิ้น
วานิชรถม้า3 ชิ้นเครื่องมือที่ต้องใช้:
แปรงทาสีหน้ากว้าง11
11
Troubleshooting
Troubleshooting
Casting rod troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
From "Fishing-Rod Making and Angling, Part I -- A One-Piece Casting Rod" by Stillman Taylor, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 59-66). His text says about 10 corks for the lower grasp; his list allows 2 dozen for both grasps. The block plane, vernier caliper and other modern tool names, and the metric figures, are ours; his tools were "a saw, plane, jackknife, file, and sandpaper" plus those in his tools section.
วัสดุ
18- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 10 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
17- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

