การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Monorail Sled: Two Tandem Plank Runners Shod With Strap Iron, Steered Lying Down (Boy Mechanic, 1915)
Woody

สร้างโดย

Woody

13. พฤศจิกายน 2026NO
7
0
0
0
0

Monorail Sled: Two Tandem Plank Runners Shod With Strap Iron, Steered Lying Down (Boy Mechanic, 1915)

Harry Hardy's monorail sled from The Boy Mechanic, Book 2 (1915): two plank runners one behind the other under a 6 ft board, shod with square-edged strap iron that grips like a skate. The rider lies full length and steers the front runner with a bar, balancing like a cyclist.
ระดับกลาง
About 1 day

คำแนะนำ

1

His sketch in centimetres

กำลังโหลดสมุด Jupyter…
2

Read The Boy Mechanic, Book 2

"Round iron or half-round iron should not be used, as these are liable to skid. The square, sharp edges of the strap iron prevent this and grip the surface just as a skate."
3

Cut and shoe the runners

Cut the two runners from 1 in plank to the size and shape of his sketch: the front runner 2 ft long, the rear one 2-1/2 ft long and about 1 ft high (the sketch prints the rear length with an inch mark; it is drawn as 2-1/2 ft). Shoe them with strap iron 1 in wide and 1/4 in thick, keeping the edges square and sharp.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
สกรูไม้สกรูไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
เลื่อยฉลุเลื่อยฉลุ
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
สว่านมือสว่านมือ
ดินสอดินสอ
ตลับเมตรตลับเมตร
4

Fit the rear runner

Nail or bolt blocks on either side of the upper edge of the rear runner and screw the top board (6 ft long, 1 in thick) to them. Brace the runner with strap iron, as in the sketch.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้สนแผ่นไม้สน1 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
สลักเกลียวหัวกลมสลักเกลียวหัวกลม1 ชิ้น
สกรูไม้สกรูไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
สว่านมือสว่านมือ
ค้อนค้อน
5

Fit the front runner and steering

Fit the front runner the same way, but with only one pair of blocks at the centre and a thin piece of wood on their tops as the fifth wheel. Bore the hole for the steering post 6 in from the front end of the top, a little larger than the post. Round the post where it passes through the hole and leave its upper end square, to take the steering bar tightly.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
สกรูไม้สกรูไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สว่านมือหมุนพร้อมดอกสว่านมือหมุนพร้อมดอก
สิ่วสิ่ว
กบไสไม้กบไสไม้
6

Troubleshooting

Monorail sled troubleshooting.

Flow

Loading...
7

History and honest limits

From "How to Make a Monorail Sled" by Harry Hardy, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 50). The rear runner length is printed 2-1/2 with an inch mark but drawn longer than the 2 ft front runner, so it is read here as 2-1/2 ft. He gives no sizes for the blocks, braces or steering bar. The tools and metric figures are ours.

วัสดุ

5

เครื่องมือที่จำเป็น

11
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • 1 vendor sell this, none ship to you yet
    ตัวยึดตำแหน่ง
  • 1 vendor sell this, none ship to you yet
    ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...