ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Ring-Disk Spiral-Pin Churn: Cream Forced Out Between Corrugated Rings, Then Drawn to the Middle by Spiral Pins
Daniel C. Brown of New York received US 26,880, dated 24 January 1860, for a churn. Cream poured into a hopper runs into the middle of a still disk at the bottom of a box, under a turning disk; their corrugated rings run between each other without touching, so the cream is flung outward and must climb over ring after ring. Above, the turning shaft carries pins set in two spirals that meet in the middle, drawing the butter there to be gathered.
The patent gives no sizes; every size here is ours.
ระดับกลาง
About 2 days, plus printing
คำแนะนำ
1
1
Rings that never touch
Rings that never touch
กำลังโหลดสมุด Jupyter…
2
2
Agitators passing between each other, two months before
Agitators passing between each other, two months before
Cornell's arms pass between those of a second shaft. Brown's rings run between the rings of a still disk.
3
3
Read US 26,880
Read US 26,880
"The milk or cream thus entering while the disk G is in rapid motion, it will be seen that (by the centrifugal force developed) the fluid will be forced outward, but, meeting the obstruction of the rings, will be checked—accumulate to some extent until forced to climb over and around them, successively advancing thus and being checked and being thereby subjected to the action of the corrugated surfaces upon each side of the rings"
4
4
Print the still disk F
Print the still disk F
A disk 236 mm across with three corrugated rings 8 mm thick and 12 tall at 40, 74 and 108 mm, a 21 mm bearing for G's journal, a 13 mm inlet beside it for the spout, and three feet. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the turning disk G
Print the turning disk G
A disk 236 mm across with two corrugated rings at 57 and 91 mm, a 20 mm journal below and a hub above with a cross hole for the shaft's pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the gear wheel
Print the gear wheel
Spur wheel, 48 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Print the geared stud's pinion
Print the geared stud's pinion
Spur pinion, 16 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
8
8
Box A, hopper B and spout C
Box A, hopper B and spout C
From 20 mm hardwood make a box 300 x 300 mm and 450 mm deep inside with a lid bored 21 mm in its middle. Bore one side 13 mm, 10 mm above the floor in its middle. Bend a 12 mm stainless tube to run from outside, through that hole along the floor and up into F's inlet, seal it through the side, and fit a stainless funnel on its outer end as the hopper. Fill the box with water overnight so it swells tight, then empty it.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง3 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้30 ชิ้น
ท่อสเตนเลส1 ชิ้น
กรวยสเตนเลส1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เลื่อยมือ
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
เลื่อยตัดเหล็ก
แคลมป์แบบบาร์
ตลับเมตร
น้ำ9
9
Disks, shaft D and pins b
Disks, shaft D and pins b
Stand F on its feet in the middle of the floor over the spout. Plane a hardwood shaft to a hexagon 40 mm across the flats and 393 mm long, with a 19 mm square socket 30 mm deep in its top, and pin its foot in G's hub. Bore twelve 16 mm holes through it from 35 to 332 mm above its foot, 27 mm apart, and glue in hardwood pins reaching 135 mm from the middle: the lower six turning 60 degrees each from the foot upward, the upper six the same from the top downward, so the two spirals meet at the middle. Set G's journal in F's bearing.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สลักผ่า1 ชิ้น
เส้นใย PETG1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เครื่องกลึงไม้
เลื่อยวงเดือนตั้งโต๊ะ
สิ่วเจาะเดือย
ค้อนไม้
สว่านไร้สาย
ชุดดอกสว่าน
กระดาษทราย10
10
Geared stud and crank E
Geared stud and crank E
Pass a 20 mm stainless stud through the lid, square at its foot to drop into the shaft's socket, with the pinion pinned on top. Fix a second stud in the lid 96 mm away carrying the gear wheel, meshing, with a crank and handle on it. Lift the lid to free the shaft and disks for cleaning.
วัสดุสำหรับขั้นตอนนี้:
แท่งสเตนเลส2 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
แหวนรองแบน4 ชิ้น
สลักผ่า2 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
สว่านไร้สาย
ชุดดอกสว่าน11
11
The build in 3D
The build in 3D
FreeCAD model of this build, cut through the middle: the box, the spout running into the still disk, the turning disk with its rings between the still disk's, the hexagonal shaft with its two spirals of pins, and the geared stud, wheel and crank on the lid. The rotor was turned through 16 positions.
12
12
Churn
Churn
Turn the crank and pour heavy cream at about 15 °C, checked with the thermometer, into the hopper, about 15 litres in all, keeping the disk turning fast. Keep turning, timing it. When the butter comes the pins gather it in the middle: lift the lid, take out the shaft and the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด15 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่13
13
Troubleshooting
Troubleshooting
Ring-disk churn troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
**Daniel C. Brown** of New York, US 26,880, 24 January 1860, "Churn". He claimed the disks F and G with the rings on their inner sides. His disks were wood or metal; ours are printed. His hopper is a jointed bucket; ours is a funnel on a tube. The patent gives no sizes; every size here is ours.
วัสดุ
14- 3 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 30 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 15 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
19- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
5พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Swinging-Wedge Churn: A Wedge Dasher Sweeps a Curved Bottom and Strikes the Sloping Ends Squarely
โดย Buttercup
งานไม้
5
0
0
0
0
0

Double Rotary Crag Churn: Two Shafts of Four-Edged Arms Turn Through Each Other in Twin Half-Cylinders
โดย Buttercup
งานไม้
13
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

