การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Cupola Furnace: the Common Foundry Cupola with a Drop Bottom (Bolland, 1893)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
11
0
0
1
0

Cupola Furnace: the Common Foundry Cupola with a Drop Bottom (Bolland, 1893)

The founder's 'common cupola': an upright steel shell lined with firebrick, standing on four columns over a drop bottom, with a wind-box round it feeding the tuyeres and a charging door high up. Coke and pig iron go in at the top in layers; blast at the tuyeres melts the iron, which runs out at the spout. Variable: the inside diameter, 24 to 84 in, which sets height, tuyeres, blower and charges. Fig. 9's 36 in cupola is 12 ft to the charging hole and takes 840 lb coke and 2520 lb iron on the bed, then 302 lb coke and 2718 lb iron per charge. Source: S. Bolland, The Iron Founder Supplement (1893), pp. 34-54. Unknown: shell plate and brick sizes. Picture: Fig. 9 of the book.
ผู้เชี่ยวชาญ
Unknown

คำแนะนำ

1

Size the cupola

Choose the inside diameter from the iron needed per hour: 10 tons in two hours (about 10,760 lb an hour) needs 48 in; 6 tons, 40 in. Make it tall enough that the gas burns before it escapes: a 50 in cupola is 14 ft from the base to the bottom of the charging hole, Fig. 9's 36 in one 12 ft. Above 60 in, keep 60 in at the tuyeres and widen above them, since the blast cannot reach the middle of a wider stock.

เครื่องมือที่ต้องใช้:

ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Build the shell, columns and drop bottom

Build a steel shell with a charging hole and door, standing on four columns. Close the bottom with swing doors on a central prop, so the whole contents can be dropped at the end of a heat. Put a slag hole a little below the tuyeres and a spout at the bottom. Ours: mild steel plate, iron castings for the bottom doors. Not given: plate thickness.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 shell, charging door
ชิ้นงานเหล็กหล่อชิ้นงานเหล็กหล่อ1 drop-bottom doors
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 columns, prop, spout

เครื่องมือที่ต้องใช้:

เครื่องเชื่อมอาร์กเครื่องเชื่อมอาร์ก
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
3

Fit the tuyeres and wind-box

Ring the cupola with a wind-box feeding the tuyeres, with a main blast pipe sized from the table (good for runs up to 100 ft). Tuyere area grows with the diameter: a 24 in cupola needs the area of 1 1/2 round 6 in tuyeres (or two flat ones 10 1/2 x 2 in), a 60 in about 13 1/2 (or eight flat 16 1/2 x 3 in), an 84 in 31 (or sixteen flat 16 x 3 1/2 in). Never reduce the tuyere area. A 42 in cupola takes a No. 3 Root blower and a 6 h.p. engine.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 wind-box
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 tuyeres, blast pipe

เครื่องมือที่ต้องใช้:

เครื่องเชื่อมอาร์กเครื่องเชื่อมอาร์ก
เครื่องเป่าลมเครื่องเป่าลม
4

Line it with firebrick

Line the shell with firebrick, every brick rubbed well down on the next and fitting the shell closely, set in mortar of the same nature as the bricks. A good lining lasts one to two years if the melter mends it each morning with thin coats of daubing, keeping its first shape. Ours: fireclay bricks and refractory clay mortar.

วัสดุสำหรับขั้นตอนนี้:

อิฐดินทนไฟอิฐดินทนไฟ1 lining
ปูนก่อดินทนไฟปูนก่อดินทนไฟ1 setting and daubing

เครื่องมือที่ต้องใช้:

เกรียงก่อเกรียงก่อ
5

Make the bed and melt

Ram a sand bottom so it lies about 10 in below the tuyeres. Lay the fuel bed, about 22 in of coke above the tuyeres (840 lb in Fig. 9's 36 in cupola), and the first iron (2520 lb), then alternate charges of coke and iron (302 lb and 2718 lb). Blow: about 30,000 cubic feet of air melts a ton of iron. On long heats flux with white marble chips and draw the slag off at the slag hole. At the end, drop the bottom.

เครื่องมือที่ต้องใช้:

ทรายทราย
ถ่านโค้กโลหการถ่านโค้กโลหการ
แท่งเหล็กดิบแท่งเหล็กดิบ
เครื่องเป่าลมเครื่องเป่าลม

วัสดุ

5

เครื่องมือที่จำเป็น

7

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...