ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
9
0
0
0
0

Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)

Ferdinand H. Dalrymple of Bedford, Ohio, received US 2,163,315, dated 20 June 1939, for a shaft collar "comprised of few parts which are readily obtainable as standard market articles". Two washers are held apart by nuts welded between them. The nuts' inner faces rest on the shaft, and a set screw in one nut's thread holds it. It needs no machining. He says it is stronger, lighter and cheaper than a cast collar, and breaks less readily under a hammer. It also touches the shaft only along lines, so it rusts to it less, and oil can be put in between the nuts. The patent gives no sizes for this form; every size here is ours.
เริ่มต้น
About 1 hour

คำแนะนำ

1

Will it fit together?

กำลังโหลดสมุด Jupyter…
2

Read US 2,163,315

"Preferably, I use as plates standard washers of suitable dimension, and I use as blocks standard nuts." "Inasmuch as the space between the plates is not sufficient for the convenient manipulation of an ordinary wrench, I use socketed set screws for securing the collar to the shaft."
3

Set the parts up on a bar

Use plain steel washers and nuts, not zinc-plated ones. Wire-brush them clean. Grip a 16 mm round bar upright in the vice. Slide one washer onto it, stand four M8 nuts on the washer round the bar at quarter turns, each with a flat down and its hole pointing at the bar's centre and its inner face against the bar. Put the second washer on top and squeeze the stack with the C-clamp; check with the square that the washers are parallel.

วัสดุสำหรับขั้นตอนนี้:

แหวนรองแบนแหวนรองแบน2 ชิ้น
น็อตหกเหลี่ยมน็อตหกเหลี่ยม4 ชิ้น

เครื่องมือที่ต้องใช้:

เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
แคลมป์ตัวซีแคลมป์ตัวซี
ชุดแปรงลวดชุดแปรงลวด
ฉากรวมอเนกประสงค์ฉากรวมอเนกประสงค์
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
4

Weld the nuts to the washers

Wearing the helmet and gloves, tack each nut to both washers with a short fillet weld at its outer corner, keeping the arc away from the bar. Let it cool, lift the collar off the bar, and run a fillet along both ends of every nut on both washers. Chip and wire-brush the slag. Run the set screw in and out of one nut to clear any spatter from its thread, and file the bore ends smooth.

วัสดุสำหรับขั้นตอนนี้:

ลวดเชื่อมลวดเชื่อม4 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องเชื่อมอาร์กเครื่องเชื่อมอาร์ก
หน้ากากเชื่อมปรับความมืดอัตโนมัติหน้ากากเชื่อมปรับความมืดอัตโนมัติ
ถุงมืองานเชื่อมถุงมืองานเชื่อม
ชุดแปรงลวดชุดแปรงลวด
เครื่องเจียรมุมเครื่องเจียรมุม
ชุดตะไบชุดตะไบ
แว่นนิรภัยแว่นนิรภัย
5

The collar in 3D

FreeCAD model, our sizes: the two 50 mm washers, the four M8 nuts between them at quarter turns, their inner faces on a 16 mm shaft, and the socket set screw in one nut. The welds are not modelled.
ไฟล์แบบSTLCC0 - Free
6

Fit it on the shaft

Run an M8 x 8 cup point socket set screw into one nut from outside. Slide the collar onto the shaft to its place and tighten the screw with the hex key between the washers. Try to slide and turn it; it must not move.

วัสดุสำหรับขั้นตอนนี้:

สกรูหนอนปลายเว้าสกรูหนอนปลายเว้า1 ชิ้น

เครื่องมือที่ต้องใช้:

ชุดประแจหกเหลี่ยมชุดประแจหกเหลี่ยม
7

Troubleshooting

Built-up collar troubleshooting.

Flow

Loading...
8

History and honest limits

**Ferdinand H. Dalrymple** of Bedford, Ohio, US 2,163,315, dated 20 June 1939, filed 2 November 1937. He claimed "opposed spaced plane plates formed with coaxial bores for the reception of a shaft, transverse spaced internally-threaded blocks welded to the opposed faces of the plates and serving as the sole means for holding the plates in relatively fixed positions, and set screws engaging the blocks". His Figs. 8 and 9 use standard square nuts and socketed set screws; we use hex nuts, as his Figs. 1-5 allow "standard nuts". His patent also shows special blocks, flanged plates, three-plate and split forms; we build the simplest. He gives no sizes for this form; every size here is ours.

วัสดุ

4

เครื่องมือที่จำเป็น

13

ไฟล์ออกแบบ

1

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...