ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Divisible Flanged Shaft Collar: Two Halves Locked by Lugs, Bolted Through the Shaft in One of Three Hole Pairs (Obey, 1916)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
11
0
0
0
0

Divisible Flanged Shaft Collar: Two Halves Locked by Lugs, Bolted Through the Shaft in One of Three Hole Pairs (Obey, 1916)

James F. Obey of Centerville, Iowa, received US 1,201,863, dated 17 October 1916, for a flanged collar that comes in two halves. It was meant for the chain rods of railway dump cars, whose collars often broke, and a whole rod then had to come out of its bearings. Lugs on one half of the flange go into slots in the other. A bolt through the rod's own hole and through a pair of openings in the collar holds it, with a nut. The collar has several pairs at different places, so it can be set in more than one position. We turn ours in one piece and saw it in half. The patent gives no sizes; every size here is ours.
ระดับกลาง
About 6 hours

คำแนะนำ

1

Where each pair of openings puts the collar

กำลังโหลดสมุด Jupyter…
2

Read US 1,201,863

"These shaft collars frequently become broken and it is one of the important purposes of my invention to provide a shaft-collar which can be quickly and easily installed on the shaft without the removal of the shaft from its bearings."
3

Turn the flanged collar

Grip 75 mm round bar in the 3-jaw chuck. Face it and turn the flange to 70 mm. Turn the hub to 32 mm for 40 mm, leaving the flange 10 mm thick. Centre-drill, drill through 15 mm and ream 16 mm. Part off at 50 mm and face the flange's outer face.

วัสดุสำหรับขั้นตอนนี้:

เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน1 ชิ้น
น้ำมันตัดกลึงน้ำมันตัดกลึง1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
หัวจับกลึงสามจับหัวจับกลึงสามจับ
มีดกลึงมีดกลึง
มีดตัดงานกลึงมีดตัดงานกลึง
ชุดดอกสว่านนำศูนย์ชุดดอกสว่านนำศูนย์
ชุดดอกสว่านชุดดอกสว่าน
ดอกรีมเมอร์ดอกรีมเมอร์
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
แว่นนิรภัยแว่นนิรภัย
4

Mark out and drill the holes

Blue the flange and hub. Scribe the split line across the flange through the centre and along both sides of the hub. Mark two chord holes across the split line, 28 mm each side of the centre, in the middle of the flange's thickness; drill them 5 mm right through the flange, square to the split line. Mark three pairs of openings round the hub, at 18, 30 and 42 mm from the flange's outer face and at 90, 30 and 150 degrees from the split line. Centre-punch, and with the collar in the V-block drill each pair 6.5 mm straight through the hub and the bore.

เครื่องมือที่ต้องใช้:

สีน้ำเงินสำหรับหาจุดสัมผัสสีน้ำเงินสำหรับหาจุดสัมผัส
เหล็กขีดเหล็กขีด
ฉากรวมอเนกประสงค์ฉากรวมอเนกประสงค์
ไม้โปรแทรกเตอร์ไม้โปรแทรกเตอร์
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
สว่านแท่นสว่านแท่น
ปากกาจับชิ้นงานของเครื่องปากกาจับชิ้นงานของเครื่อง
วีบล็อกวีบล็อก
ชุดดอกสว่านชุดดอกสว่าน
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
5

Saw it in half and fit the lugs

In soft jaws, saw down the split line through flange and hub with a fine hacksaw blade, through the middle of the chord holes. File the cut faces flat. Tap a 5 mm steel dowel pin 20 mm long into each chord hole of one half, leaving 9 mm sticking out: these are the lugs, and the other half's holes are the slots. Put the halves together: they must close with only the saw cut between them, and slide apart only straight.

วัสดุสำหรับขั้นตอนนี้:

สลักเดือยเหล็กสลักเดือยเหล็ก2 ชิ้น

เครื่องมือที่ต้องใช้:

ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ปากอ่อนสำหรับปากกาจับชิ้นงานปากอ่อนสำหรับปากกาจับชิ้นงาน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ชุดตะไบชุดตะไบ
ค้อนหัวกลมค้อนหัวกลม
เครื่องมือลบครีบเครื่องมือลบครีบ
6

The collar in 3D

FreeCAD model, our sizes: the two halves with flange and hub on a 16 mm shaft, the two pins across the split in the flange, the three pairs of openings, and the M6 bolt and nut through the first pair and the shaft.
ไฟล์แบบSTLCC0 - Free
7

Drill the shaft and fit the collar

Mark where the collar's flange must stand and drill a 6.5 mm hole straight across the shaft, 18 mm from that mark, with the shaft in the V-block. Put the two halves round the shaft from the sides, the lugs into the slots, and turn the collar until the 18 mm pair lines up with the hole. Push an M6 x 50 bolt through and tighten a nyloc nut on it. To move the collar, take the bolt out, slide and turn the collar until another pair lines up, and bolt it again.

วัสดุสำหรับขั้นตอนนี้:

ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด1 ชิ้น
นอตล็อกไนลอนนอตล็อกไนลอน1 ชิ้น

เครื่องมือที่ต้องใช้:

สว่านแท่นสว่านแท่น
วีบล็อกวีบล็อก
ชุดดอกสว่านชุดดอกสว่าน
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
ประแจเลื่อนประแจเลื่อน
8

Troubleshooting

Obey collar troubleshooting.

Flow

Loading...
9

History and honest limits

**James F. Obey** of Centerville, Appanoose County, Iowa, US 1,201,863, dated 17 October 1916, filed 3 August 1915. He claimed a shaft with a transverse hole, "a collar mounted thereon consisting of a longitudinally halved cylinder with an annular flange at one end, one half of the flange being provided with lugs, the other half being provided with corresponding slots", pairs of aligned openings at different points along and round the cylinder, and a bolt through the shaft's hole and a chosen pair. His lugs are bent pieces on the face of the flange that hook into yokes on the other half; ours are pins in holes through the flange, which do the same job. His bolt has a round head; ours is a hex bolt with a nyloc nut. The patent gives no sizes or material; every size here is ours.

วัสดุ

5

เครื่องมือที่จำเป็น

24

ไฟล์ออกแบบ

1

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...