ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Digital Kitchen Scale: a Cantilever Load Cell in a Sealed Dual Housing (Edlund, 2009)
A digital scale built to survive a kitchen: spills, washing and being dropped. The load cell is a short cantilever with a strain sensor on top, and the electronics sit in a sealed compartment. Both are in a plastic chassis held loosely inside a second, outer housing of stainless steel and plastic, with crushable spacers between the two.
Result: a digital kitchen scale with a removable pan, sealed display and touchpad, battery power and an overload stop under the load cell.
Source: R. S. Whitney (Edlund Company), US Patent 7,554,043 (2009). Unknown: sizes, capacity, resolution and the electronics; the patent says suitable force transducers are readily available. Ours: the display and button types. Picture: Wikimedia Commons.
ขั้นสูง
2 days
คำแนะนำ
1
1
Mount the cantilever load cell
Mount the cantilever load cell
In the load-cell cavity of the plastic chassis, screw a base plate to the cavity floor. Screw the cantilever support to the base plate; a support plate on the cantilever carries the posts for the pan. A strain transducer on top of the cantilever senses the top stretching as it bends under a load. A window in the base plate leaves the cavity floor just below the free end, so an overload bottoms out there instead of breaking the transducer.
วัสดุสำหรับขั้นตอนนี้:
โหลดเซลล์1 cantilever type
พลาสติก1 chassis
สกรูเกลียวมิล1 ชุดเครื่องมือที่ต้องใช้:
ชุดไขควง
ขนาดที่ไม่ทราบ2
2
Seal in the electronics
Seal in the electronics
On the other side of the chassis, fit the display electronics behind one opening and the touchpad electronics behind another, wired to the strain transducer through sealing bushings. Fit a battery holder. Close the compartment with its cover on gaskets, so the electronics stay dry. Not given: the circuit, the display and the battery. Ours: a segment LCD and push buttons.
วัสดุสำหรับขั้นตอนนี้:
วงจรรวม1 weighing and display electronics
จอแอลซีดีแบบเซกเมนต์1 ชิ้น
ปุ่มกด1 touchpad keys
แบตเตอรี่1 ชิ้น
ปะเก็นกันรั่ว2 ชิ้น
สายไฟต่อวงจร1 short
ลวดตะกั่วบัดกรี1 a littleเครื่องมือที่ต้องใช้:
หัวแร้งบัดกรี
ชุดไขควง3
3
Close it in the outer housing
Close it in the outer housing
Place the chassis, unfastened, between the two halves of the outer housing: a stainless-steel top with downturned sides, and a plastic bottom. Spacers moulded on the chassis sides press against the housing sides. They take a blow if the scale is dropped, and may crush on purpose to save the load cell and electronics. A sealed window of plastic or glass shows the display. A flexible sheet covers the touchpad. Fit four height-adjustable feet.
วัสดุสำหรับขั้นตอนนี้:
แผ่นสเตนเลส1 upper housing
พลาสติก1 lower housing
วัสดุที่ไม่ทราบ1 window, touchpad sheet, four feetเครื่องมือที่ต้องใช้:
ชุดไขควง
ขนาดที่ไม่ทราบ4
4
Fit the pan and check
Fit the pan and check
Screw the pan support to the four supports of the load cell. Rest the removable pan on it, or snap it on, so it lifts off for washing. A flexible boot can seal each support where it passes through the housing. Ours: check the reading with calibration weights.
วัสดุสำหรับขั้นตอนนี้:
จานชั่ง1 metal or plastic
สกรูเกลียวมิล1 ชุดเครื่องมือที่ต้องใช้:
ชุดไขควง
ชุดตุ้มน้ำหนักสอบเทียบวัสดุ
13- 1 cantilever typeตัวยึดตำแหน่ง
- 1 lower housingตัวยึดตำแหน่ง
- 2 ชุดตัวยึดตำแหน่ง
- 1 weighing and display electronicsตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 shortตัวยึดตำแหน่ง
- 1 a littleตัวยึดตำแหน่ง
- 1 upper housingตัวยึดตำแหน่ง
- 1 window, touchpad sheet, four feetตัวยึดตำแหน่ง
- 1 metal or plasticตัวยึดตำแหน่ง
วัสดุจากพิมพ์เขียวที่เชื่อมต่อ

การระบุ 10%
Mechanical Kitchen Scale: Sheet-Metal Case, Guided Plate and Two Springs to a Dial (Hansen, 1939)
โดย Penny
กลศาสตร์
13
0
0
0
1
0

การระบุ 10%
Electronic Baby Scale That Holds a Steady Reading: Hino & Itani, 1981
โดย Penny
อิเล็กทรอนิกส์
31
0
0
0
2
0

การระบุ 10%
Strain-Gauge Load Cell with Floating Piston: Ruge, 1949
โดย Penny
อิเล็กทรอนิกส์
31
0
0
0
3
0
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

