ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Trundle-and-Pitman Churn: One Crank Turns the Dasher Staff and Lifts It Up and Down at Once
Martin

สร้างโดย

Martin

9. พฤศจิกายน 2026NO
8
0
0
0
0

Trundle-and-Pitman Churn: One Crank Turns the Dasher Staff and Lifts It Up and Down at Once

Edward L. Dorsey of Greenwood, Indiana, received US 23,556, dated 12 April 1859, for giving a churn's dashers two motions at once. A crank turns a wheel with teeth on its face. The teeth work between the rounds of a trundle (lantern) wheel on the dasher staff and turn it, while a pin on the same wheel works a pitman that lifts and drops the staff. The staff carries a round dasher at its foot and an armed whipping dasher above; the up-and-down dasher keeps the cream from simply swirling round. This rung builds it in wood and steel rod on a square food container.
ระดับกลาง
About 8 hours

คำแนะนำ

1

Two motions from one crank

กำลังโหลดสมุด Jupyter…
2

A crank that lifts the dasher, before it

Rarey's crank only lifted the dasher. Dorsey's turns it as well, from the same wheel.
3

Read US 23,556

"... the teeth of wheel H work between the rounds n, n, n, of trundle wheel C, and give a circular motion to the said dashers. Thus the staff and dashers have two distinct motions—a vertical reciprocating and a rotary motion."
4

Body A, top and upright B

Use a square food-grade container about 300 x 300 x 320 mm. Cut an 18 mm plywood top 340 mm square with a 24 mm hole in the middle for the staff, and screw two cleats underneath so it sits square on the rim. Screw a hardwood upright B 44 x 44 mm, 300 mm tall, to the top, its near face 110 mm from the hole, and bore it 12.5 mm square to the top, 260 mm above it.

วัสดุสำหรับขั้นตอนนี้:

ภาชนะเก็บเกรดอาหารภาชนะเก็บเกรดอาหาร1 ชิ้น
แผ่นไม้อัดแผ่นไม้อัด1 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
สกรูไม้สกรูไม้10 ชิ้น
กาวไม้กาวไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดไขควงชุดไขควง
ตลับเมตรตลับเมตร
5

Wheel H and shaft I

Cut an 18 mm plywood disc 300 mm across. Drill 36 holes 8 mm across, evenly round a 280 mm circle, and glue in 8 mm hardwood dowels standing 16 mm proud of the front face as the teeth. Drill an 8 mm hole 45 mm from the centre and press in an 8 mm steel pin 16 mm proud as pin o. Glue a hardwood hub 60 mm across on the back. Fix a 12 mm stainless rod through hub and disc with an M4 screw across as shaft I, pass it through the upright, and fix a hardwood crank D 132 mm long with a dowel handle on its far end.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้อัดแผ่นไม้อัด1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
สกรูเกลียวมิลสกรูเกลียวมิล2 ชิ้น
นอตล็อกไนลอนนอตล็อกไนลอน2 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
กระดาษทรายกระดาษทราย
ชุดไขควงชุดไขควง
6

Staff E, trundle C and dashers

Cut two hardwood heads M 74 mm across and 6 mm thick, bore each 20 mm in the middle and drill 8 holes 8 mm across on a 62 mm circle; glue in 8 dowel rounds n 116 mm long. Cut a 20 mm hardwood dowel 594 mm long as staff E and drill an 8.5 mm hole across it 14 mm below its top. Cut dasher J, an 18 mm plywood disc 200 mm across with six 28 mm holes, and dasher K, two plywood arms 230 x 24 mm halved into a cross. Glue J on the staff's foot, K 112 mm above it and the trundle where its middle meets the teeth with the staff halfway up its stroke.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
แผ่นไม้อัดแผ่นไม้อัด1 ชิ้น
กาวไม้กาวไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดโฮลซอว์ชุดโฮลซอว์
แคลมป์แคลมป์
กระดาษทรายกระดาษทราย
7

Pitman F

Bend an 8 mm stainless rod in the vise: a small eye at one end to go on pin o, then a straight length 80 mm from the eye's centre to a right-angle bend, then a leg 56 mm long that goes across through the hole in the staff's top as the pivot. Put the staff in through the top, set the eye on pin o with a washer and lock nut, and push the leg through the staff.

วัสดุสำหรับขั้นตอนนี้:

แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
แหวนรองแบนแหวนรองแบน1 ชิ้น
นอตล็อกไนลอนนอตล็อกไนลอน1 ชิ้น

เครื่องมือที่ต้องใช้:

ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ประแจเลื่อนประแจเลื่อน
8

The build in 3D

FreeCAD model of this build, the near half of the container cut away: the top and upright, wheel H with its dowel teeth and pin o, shaft I and crank D, the pitman bent into the staff's top, trundle C, and dashers K and J. It was checked for clashes at 12 crank positions through a full turn.
ไฟล์แบบBLENDCC0 - Free
9

Churn

Lift the top, pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and set the top back. Turn the crank steadily and time it: the dashers turn and rise and fall together. When the butter comes, lift the top and staff out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด12 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
10

Troubleshooting

Trundle-and-pitman churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Edward L. Dorsey** of Greenwood, Johnson County, Indiana, US 23,556, 12 April 1859, "Churn". He found it best in a square box, the rising and falling lower dasher checking the swirl the upper one gives. He claimed the trundle wheel, staff, pitman and cog wheel together. He gave no sizes or materials: every size and material here is ours.

วัสดุ

13

เครื่องมือที่จำเป็น

18

ไฟล์ออกแบบ

1

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...