การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)
Swages, the smith's top and bottom tools for bringing a weld back to round or square, from George Edwinson's smithing series in Amateur Work (1886): steel or steel-faced iron made like a fuller, the bottom tool tanged for the anvil's square hole, the top tool on a withy or iron-rod handle, or the pair coupled by a steel spring for single-handed work.
ขั้นสูง
A day at the forge per pair
คำแนะนำ
1
1
Read Edwinson
Read Edwinson
"They may be made of steel throughout, or of steel-faced iron. The method of making them is similar to that for making fullers and setts."
2
2
Weld the blanks
Weld the blanks
As for a fuller: upset an iron bar, split it into a fork with a hot set, weld in a forged steel wedge. Or use steel throughout.
วัสดุสำหรับขั้นตอนนี้:
แท่งเหล็กดัด1 ชิ้น
เหล็กกล้าเบ้าหลอม1 ชิ้น
ผงบอแรกซ์1 ชิ้นเครื่องมือที่ต้องใช้:
เตาตีเหล็กของช่างตีเหล็ก
ทั่ง
ค้อนปอนด์
สกัดร้อน
คีมช่างตีเหล็ก3
3
Bottom swage
Bottom swage
Forge the steel face into a block with a square tang that fits the square hole in the tail of the anvil, like a bottom set (his figs. 285-288).
เครื่องมือที่ต้องใช้:
เตาตีเหล็กของช่างตีเหล็ก
ทั่ง
ค้อน
คีมช่างตีเหล็ก4
4
Top swage
Top swage
Forge the matching top tool with a neck for its handle.
เครื่องมือที่ต้องใช้:
เตาตีเหล็กของช่างตีเหล็ก
ทั่ง
ค้อน
คีมช่างตีเหล็ก5
5
Cut the grooves
Cut the grooves
Form the working groove in each face to the section you need: round, half-round, oval, diagonal, square or rectangular. Groove sizes are ours: match the bars you forge.
เครื่องมือที่ต้องใช้:
เตาตีเหล็กของช่างตีเหล็ก
ฟุลเลอร์ (เหล็กเซาะร่อง)
ทั่ง
ตะไบ (ตะไบมือ)6
6
Handle or spring
Handle or spring
Give the top tool a hazel-rod or iron-rod handle as for fullers and top sets. For single-handed work, couple the top and bottom tools with a steel spring (fig. 283).
วัสดุสำหรับขั้นตอนนี้:
กิ่งเฮเซล (สด ดัดได้)1 ชิ้น
เหล็กเส้นกลมเหล็กกล้าละมุน1 ชิ้น
ลวดเหล็กดัด1 ชิ้น
แถบเหล็กสปริง1 ชิ้นเครื่องมือที่ต้องใช้:
เตาตีเหล็กของช่างตีเหล็ก
ทั่ง
ค้อน7
7
Grind and harden
Grind and harden
Grind the faces level so they fit each other, then heat the whole tool and harden it (his note for hand-worked dies).
เครื่องมือที่ต้องใช้:
หินลับแบบหมุน
เตาตีเหล็กของช่างตีเหล็ก
ถังชุบน้ำ8
8
Use them
Use them
Work the weld at a red heat. Hold the bar and the top swage; the striker hits the top tool with a light sledge. Pass the bar to and fro, turning it for round. After each heat gauge the weld in the swage block or with callipers.
เครื่องมือที่ต้องใช้:
เตาตีเหล็กของช่างตีเหล็ก
ค้อนปอนด์
เวอร์เนียคาลิปเปอร์9
9
Troubleshooting
Troubleshooting
Swage troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From George Edwinson, "Smithing and Forging" XI, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 259-260 and figs. 283-290 (checked on the archive.org scan amateurworkillus06lond). The forging steps follow his fuller method (pp. 14-16). Groove sizes, the spring stock and the tools are ours.
วัสดุ
7- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
11- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้




