การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Leader Harness Long Crupper: Folded Dock, Lay, Hip Straps, Carrier Straps and Tugs (Hasluck, Harness Making, 1904)
The leader horse's long crupper (F in Fig. 102) runs from the collar straps along the back to the tail, and carries the hip straps (H) that hold up the chain traces and the carrier straps (L) for the stretcher. This is the long crupper from Paul N. Hasluck's Harness Making (1904), with its folded dock, lay, 3 in dee, hip-strap tugs (K) and stretcher strap (M). Every size is his.
ขั้นสูง
About 1-2 days
คำแนะนำ
1
1
His sizes in centimetres
His sizes in centimetres
กำลังโหลดสมุด Jupyter…
2
2
Read Harness Making, ch. VIII
Read Harness Making, ch. VIII
"Cut the crupper from good leather 3 ft. 8 in. long and 5 in. wide, and make a split 9 in. long at the light end and another, 7 in. long, at the tail end."
3
3
Cut the body
Cut the body
Cut the crupper 3 ft 8 in by 5 in. Slit the light end 9 in and the tail end 7 in, leaving the points of the slits the full width in front and only cutting a little out of the corners. Narrow the tail-end points gradually to about 1-1/8 in and cut a little from the sides of each slit. Cut a lining for a foot or so of the tail end.
วัสดุสำหรับขั้นตอนนี้:
หนังทำเครื่องม้า1 ชิ้นเครื่องมือที่ต้องใช้:
มีดตัดหนัง
ตลับเมตร4
4
Fold the dock
Fold the dock
Cut soft leather 16 in by 3-1/2 in for the dock and shave the ends thin. Damp it well and turn both edges down so they overlap deeply along the centre. Bring both ends together, sides meeting flat but not flat sides together; holding the piece flat in the centre, turn the lower edge inwards and upwards, keeping the points together with the other hand. Nail each point to a board and keep it in shape until dry, when the dock will be firm.
วัสดุสำหรับขั้นตอนนี้:
หนังแกะเบซิล1 ชิ้น
ตะปู1 ชิ้นเครื่องมือที่ต้องใช้:
มีดตัดหนัง
ฟองน้ำ
ค้อน
แผ่นไม้สน5
5
Finish the body and put in the dock
Finish the body and put in the dock
Edge, crease and black the body, making two rows all round; rub the edges well and hot-crease the lines. At the tail end prick the second line as far as the double runs. When the dock is dry, put it between the lining and body at each end of the slit, tack it down round the lining and stitch. A few egg-shaped stitches inside the outer stitches, through the body and dock points, keep the dock in place. Trim the edges and black, rub and tallow them, and the inside edges of the slits too.
วัสดุสำหรับขั้นตอนนี้:
สีย้อมหนัง1 ชิ้น
ไขสัตว์1 ชิ้น
ตะปูยึดขึ้นหุ่น1 ชิ้น
ด้ายหนัง1 ชิ้น
ขี้ผึ้ง1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องมือลบมุมขอบ
เครื่องมือกรีดพับ
หัวพ่นไฟโพรเพน
เครื่องมือขัดขอบหนัง
สิ่วตอกรูหนัง
ค้อน
เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่ม
ปากคีบไม้สำหรับเย็บหนัง6
6
Fit the front buckles
Fit the front buckles
Cut two chapes to hold the buckles in front that fasten the crupper to the collar straps; bend them down about 4 in, shave one end and point the other, and cut a hole for the buckle. Tack two loops about 1-1/2 in wide in place, keeping the outside of each buckle exactly level with the end of its slit and the chapes right in the centre. Stitch them down, put a cross stitch on each side of the buckle, and shape and crease the loops.
วัสดุสำหรับขั้นตอนนี้:
หนังทำเครื่องม้า1 ชิ้น
หัวเข็มขัดเหล็กมีลิ้น2 ชิ้น
ด้ายหนัง1 ชิ้น
ขี้ผึ้ง1 ชิ้นเครื่องมือที่ต้องใช้:
มีดตัดหนัง
แท่งขึ้นรูปห่วงสาย
เครื่องมือกรีดพับ
หัวพ่นไฟโพรเพน
เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่ม
ปากคีบไม้สำหรับเย็บหนัง7
7
Make the lay, hip straps and carrier straps
Make the lay, hip straps and carrier straps
Cut the lay 1 ft 3 in by 3 in, turn it down for about 1 ft at the good end, shave the end of the short turn thin and round the other end; edge, crease and black it. Cut two hip straps 2 ft by 1-1/2 in, turn them down 3 in at the heavy end, shave the turn-down, point the buckle end, and crease and black them. Attach them to a 3 in japanned or tinned dee, one on each side, with four rows of stitching in the double of each; rub and finish the edge. Make two carrier straps the same way, each 2 ft 10 in by 1-1/4 in, and stitch them in the middle round part of the dee between the hip straps.
วัสดุสำหรับขั้นตอนนี้:
หนังทำเครื่องม้า1 ชิ้น
ห่วงตัว D เครื่องเทียมม้า1 ชิ้น
สีย้อมหนัง1 ชิ้น
ด้ายหนัง1 ชิ้น
ขี้ผึ้ง1 ชิ้นเครื่องมือที่ต้องใช้:
มีดตัดหนัง
เครื่องมือลบมุมขอบ
เครื่องมือกรีดพับ
หัวพ่นไฟโพรเพน
เครื่องมือขัดขอบหนัง
เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่ม
ปากคีบไม้สำหรับเย็บหนัง
ตลับเมตร8
8
Stitch the dee and lay to the body
Stitch the dee and lay to the body
Put the straight part of the dee in the bend of the lay and place it on the centre of the crupper body, the same distance from each side, with the extreme point of the dee within 8 in of the points of the tail slits. Tack down and stitch two rows 1/4 in apart all round, eight per inch, with three-cord thread; then stitch the lay coarse, or spot it across just to the dee. Some makers put a pad under the crupper, as on the cart-saddle crupper, from the end of the tail slit to 1 in beyond the point of the lay.
วัสดุสำหรับขั้นตอนนี้:
ตะปูยึดขึ้นหุ่น1 ชิ้น
ด้ายหนัง1 ชิ้น
ขี้ผึ้ง1 ชิ้นเครื่องมือที่ต้องใช้:
ค้อน
สิ่วตอกรูหนัง
เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่ม
ปากคีบไม้สำหรับเย็บหนัง9
9
Make the hip-strap tugs and stretcher strap
Make the hip-strap tugs and stretcher strap
With a pair of 1-1/2 in hip-strap chains, cut the tugs 10 in by 1-1/2 in; bend them so the points meet in the centre, cut a hole for the buckle in one end, stitch the points together and put in two narrow loops (one hides the joint) or one broad loop. Stitch a safe underneath. For the stretcher carrier tug, cut a strap 1-1/4 in by 1 ft 2 in, bend a chape in it and cut a hole for the buckle; stitch the buckle on with a loop, and make a running loop and a hole 1 in from the point of the strap.
วัสดุสำหรับขั้นตอนนี้:
โซ่เหล็ก2 ชิ้น
หนังทำเครื่องม้า1 ชิ้น
หัวเข็มขัดเหล็กมีลิ้น3 ชิ้น
ด้ายหนัง1 ชิ้น
ขี้ผึ้ง1 ชิ้นเครื่องมือที่ต้องใช้:
มีดตัดหนัง
แท่งขึ้นรูปห่วงสาย
เครื่องเจาะรูหนัง
เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่ม
ปากคีบไม้สำหรับเย็บหนัง10
10
Put the gear together
Put the gear together
Fix a loop on each end of the stretcher and nail its ends, leaving room for the strap to pass. Put the runner loop on the strap, run the strap down through the stretcher loop and back through the runner to the buckle; secure the carrier straps to the same buckle, their points down in the loop, and keep the runner down by the stretcher. Buckle the hip straps into the tug buckles, hook the chain traces on, and buckle the collar straps into the front buckles. The dock under the tail is optional: the hip straps fastened in the dee keep the crupper in place.
วัสดุสำหรับขั้นตอนนี้:
หนังทำเครื่องม้า1 ชิ้น
ตะปู1 ชิ้นเครื่องมือที่ต้องใช้:
ค้อน
มีดตัดหนัง11
11
Troubleshooting
Troubleshooting
Long crupper troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
From **Harness Making**, edited by Paul N. Hasluck, Cassell, 1904 (Project Gutenberg 70169), chapter VIII, "Fore Gear or Leader Harness", pp. 101-104, Figs. 102-104; every fraction was checked on the archive.org scan (harnessmaking00hasl). The stretcher (the bar that keeps the traces apart) is not made here. Basil for the "soft leather" dock, the buckle count in the list, the tools and metric figures are ours.
วัสดุ
11- 5 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 5 ชิ้นตัวยึดตำแหน่ง
- 5 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
15- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้


