การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Plough Coupling Strap: Cross-Strap With Buckled Billets for a Pair of Horses (Hasluck, Harness Making, 1904)
When two horses plough side by side, a coupling strap ties them together so they keep level. This is the coupling from Paul N. Hasluck's Harness Making (1904): a 1 in strap 28 in to 30 in long with a buckled billet at each end, buckled from the mouth of one horse to the other. Every size is his; the picture is our diagram.
เริ่มต้น
About 2 hours
คำแนะนำ
1
1
His sizes in centimetres
His sizes in centimetres
กำลังโหลดสมุด Jupyter…
2
2
Read Harness Making, ch. IX
Read Harness Making, ch. IX
"Couplings are also a necessary part of plough gear. In some localities only cross-straps are employed from mouth to mouth when ploughing in pairs."
3
3
Cut the strap
Cut the strap
Cut the strap 1 in wide and 28 in to 30 in long. Turn it in about 1 in at each end, make a hole for the buckle, and shave the points.
วัสดุสำหรับขั้นตอนนี้:
หนังทำเครื่องม้า1 ชิ้นเครื่องมือที่ต้องใช้:
มีดตัดหนัง
เครื่องเจาะรูหนัง
ตลับเมตร4
4
Make the billets
Make the billets
Cut two billets the same width, 1 ft long; trim them to a point at one end and shave the other. Edge them and crease them (the book prints "edge back, and crease them", probably for "edge, black").
วัสดุสำหรับขั้นตอนนี้:
หนังทำเครื่องม้า1 ชิ้น
สีย้อมหนัง1 ชิ้นเครื่องมือที่ต้องใช้:
มีดตัดหนัง
เครื่องมือลบมุมขอบ
เครื่องมือกรีดพับ
หัวพ่นไฟโพรเพน5
5
Put it together
Put it together
Put the buckle in, then the thin end of the billet 2 in down at the back of the buckle. Put a loop between the chape by the buckle, and stitch one billet and buckle at each end. Punch two holes in each billet.
วัสดุสำหรับขั้นตอนนี้:
หัวเข็มขัดเหล็กมีลิ้น2 ชิ้น
หนังทำเครื่องม้า1 ชิ้น
ด้ายหนัง1 ชิ้น
ขี้ผึ้ง1 ชิ้นเครื่องมือที่ต้องใช้:
แท่งขึ้นรูปห่วงสาย
เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่ม
ปากคีบไม้สำหรับเย็บหนัง
เครื่องเจาะรูหนัง6
6
Crossing couplings for a pair
Crossing couplings for a pair
Sometimes two coupling straps are used for a pair, crossing each other from the hames of each horse to the mouth of the other. Make them the same way but longer: 38 in, each with 12 in billets. Some are made a foot longer and cut in two, one end 15 in long with a buckle and loop and the other made to buckle on, with many holes. Then the coupling can be shortened on a young horse's side, to keep it back until it has learned the ordinary working pace.
วัสดุสำหรับขั้นตอนนี้:
หนังทำเครื่องม้า1 ชิ้น
หัวเข็มขัดเหล็กมีลิ้น4 ชิ้น
ด้ายหนัง1 ชิ้น
ขี้ผึ้ง1 ชิ้นเครื่องมือที่ต้องใช้:
มีดตัดหนัง
แท่งขึ้นรูปห่วงสาย
เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่ม
เครื่องเจาะรูหนัง
ตลับเมตร7
7
Troubleshooting
Troubleshooting
Coupling strap troubleshooting.
Flow
Loading...
8
8
History and honest limits
History and honest limits
From **Harness Making**, edited by Paul N. Hasluck, Cassell, 1904 (Project Gutenberg 70169), chapter IX, "Plough Harness", couplings, pp. 110-111; every figure was checked on the archive.org scan (harnessmaking00hasl). He gives no buckle size; a 1 in buckle suits the 1 in strap. The picture is our diagram from his text. The tools and metric figures are ours.
วัสดุ
5- 4 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
10- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้


