ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Heat Exchanger: the Double-Pipe Residual Exchanger (Bell, 1923)
A heat exchanger built from stock pipe: runs of one pipe inside another, joined by return bends. Hot residuum from the stills flows one way in the outer pipe while cold crude flows the other way in the inner one, so the crude reaches the stills already warm.
Variable: 2 in within 3 in, or 3 in within 4 in, and the number of runs (Bell's Fig. 73 has 16). Expect a transfer rate of 14 to 18 B.t.u.
Source: H. S. Bell, American Petroleum Refining (1923), pp. 156-162. Unknown: run length, packing. Picture: Fig. 73 of the book.
ขั้นสูง
Unknown
คำแนะนำ
1
1
Choose the pipe pair
Choose the pipe pair
Use 2 in pipe inside 3 in, or 3 in inside 4 in. Plan the number of runs (Fig. 73: 16 runs of 2 in in 3 in). Not given: run length.
เครื่องมือที่ต้องใช้:
ขนาดที่ไม่ทราบ2
2
Put up the supports
Put up the supports
Stand up channel-iron supports and bolt the runs to them, stacked so the bends line up at each end (Fig. 73).
วัสดุสำหรับขั้นตอนนี้:
เหล็กรูปตัวยู1 supports
สลักเกลียวหัวหกเหลี่ยม - เกรด 8.81 ชิ้นเครื่องมือที่ต้องใช้:
ประแจจับท่อ3
3
Assemble the runs
Assemble the runs
Slide each inner pipe into its outer pipe. At one end join the outer pipes with 3 in return bends whose stuffing boxes the 2 in pipe passes through; make the boxes extra deep, because hot oil penetrates. Join the inner pipes with 2 in return bends with unions. Use heavy fittings; steel ones on the first runs where the oil is 460 °F or hotter.
วัสดุสำหรับขั้นตอนนี้:
ท่อเหล็ก (ผนังหนา ปลายเกลียว)1 2 in and 3 in runs
ข้อต่อท่อเกลียว1 return bends, unions, stuffing boxes
วัสดุอัดกันรั่วที่ไม่ทราบ1 stuffing boxesเครื่องมือที่ต้องใช้:
ประแจจับท่อ4
4
Connect the headers
Connect the headers
Run counter-current: hot residuum from the stills enters the outer pipes from a 3 in header and leaves cold to storage by another; cold oil from storage enters the inner pipes from a 2 in header and leaves hot to the stills. Valve the headers.
วัสดุสำหรับขั้นตอนนี้:
ท่อเหล็ก (ผนังหนา ปลายเกลียว)1 headers
วาล์วประตูน้ำ2 ชิ้นเครื่องมือที่ต้องใช้:
ประแจจับท่อวัสดุ
6- 1 supportsตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 headersตัวยึดตำแหน่ง
- 1 return bends, unions, stuffing boxesตัวยึดตำแหน่ง
- 1 stuffing boxesตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
2- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
วัสดุจากพิมพ์เขียวที่เชื่อมต่อ
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

