การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Instant-Read Thermometer: Digital, with a Stainless Probe That Pivots on the Case (Cook, US 5,018,875, 1991)
A pocket digital thermometer. A thin stainless steel probe with a thermistor in its tip pivots on a small, flat-sided case, so you can push the probe into food and turn the display to face you. A button cell runs a chip and a liquid crystal display, and a push button updates the reading at once. The angled case will not roll off a table.
Result: a thin-probe digital thermometer for food and air.
Source: T. A. Cook (PSG Industries), US 5,018,875 (1991). Unknown: the circuit, the range, the case size. Picture: the patent drawing.
ระดับกลาง
Unknown
คำแนะนำ
1
1
Make the probe
Make the probe
Cut a type 304 stainless steel tube about 0.166 in (4.0 mm) across and 5 in (120 mm) long, and close one end. Set a thermistor inside the closed tip and run its two wires up the tube. Aluminium or titanium would also serve.
วัสดุสำหรับขั้นตอนนี้:
ท่อสเตนเลส1 probe
ชุดเทอร์มิสเตอร์ NTC1 thermistor
ลวดทองแดง1 interconnecting wiresเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
หัวแร้งบัดกรี2
2
Mould the pivot boss and case
Mould the pivot boss and case
Mould from ABS a cylindrical pivot boss with a recess for the probe's open end and a channel right through it for the wires. Mould the case in an upper and a lower half that snap together, wider at the display end and tapering to the probe end so it cannot roll, with two projecting supports at the probe end, each with a pivot hole. Not given: the sizes.
วัสดุสำหรับขั้นตอนนี้:
เม็ดพลาสติก ABS1 boss and caseเครื่องมือที่ต้องใช้:
เครื่องฉีดพลาสติก
ขนาดที่ไม่ทราบ3
3
Fit the electronics and assemble
Fit the electronics and assemble
In the case, fit an integrated circuit that turns the thermistor's resistance into a reading on a liquid crystal display at the wide end, with a push button beside it that updates the reading at once. Add a compartment for a 1.5 V button cell (Eveready E675, IEC R07) under a cover that locks with a quarter turn. Push the probe into the boss, lead the wires through the channel to the circuit, and clamp the boss ends in the pivot holes as the halves snap together; friction holds whatever angle you set. In use, push the probe in, turn the display to face you and press the button. Not given: the circuit (the patent points to US 4,536,851).
วัสดุสำหรับขั้นตอนนี้:
แผ่นวงจรพิมพ์1 ชิ้น
วงจรรวม1 ชิ้น
จอแอลซีดีแบบเซกเมนต์1 ชิ้น
ปุ่มกด1 ชิ้น
ถ่านกระดุม 1.5 โวลต์1 ชิ้น
ลวดตะกั่วบัดกรี1 as neededเครื่องมือที่ต้องใช้:
หัวแร้งบัดกรีวัสดุ
10- 1 probeตัวยึดตำแหน่ง
- 1 thermistorตัวยึดตำแหน่ง
- 1 interconnecting wiresตัวยึดตำแหน่ง
- 1 boss and caseตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 as neededตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
4- ตัวยึดตำแหน่ง
- 2 vendors sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
วัสดุจากพิมพ์เขียวที่เชื่อมต่อ
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้



