ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Lead-Lined Tank: a Steel Acid Tank with an Antimonial Lead Lining (Bell, 1923)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
9
0
0
1
0

Lead-Lined Tank: a Steel Acid Tank with an Antimonial Lead Lining (Bell, 1923)

A riveted steel tank lined with sheet lead, for weak sulphuric acid, which eats bare steel. The lead hangs from the top angle and is held to the shell by steel straps covered with lead burned to the lining. Bell's example (Fig. 170) is a vertical tank 15 ft across and 10 ft high, lined with 6 % antimony lead at 7 1/2 lb per sq ft. Source: H. S. Bell, American Petroleum Refining (1923), pp. 305-306. Picture: Fig. 170 of the book.
ผู้เชี่ยวชาญ
Unknown

คำแนะนำ

1

Build the steel tank

Build the shell as a standard riveted vertical tank, with plate at least 3/8 in thick. Drive the rivets with flat heads 1/16 to 1/8 in high inside, and leave out an occasional rivet so leaks in the lining can be found. The shell plates need not be bevelled or caulked. If you can, stand it on concrete piers with steel I-beams so the bottom can be inspected, and protect the concrete with coal tar or petroleum pitch.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 3/8 in min.
หมุดย้ำเหล็กกล้าหมุดย้ำเหล็กกล้า1 ชิ้น

เครื่องมือที่ต้องใช้:

ค้อนย้ำหมุดค้อนย้ำหมุด
ชันจากน้ำมันดินถ่านหินชันจากน้ำมันดินถ่านหิน
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Cut the lead

Use chemical lead at 8 lb per sq ft, or 6 % antimony lead at 7 1/2 lb per sq ft. For Bell's 15 x 10 ft tank: 7 sheets 10 ft 11 in x 7 ft 2 in, 7 sheets 10 ft 11 in x 7 in, and 2 half-circle sheets of 8 ft radius for the bottom.

วัสดุสำหรับขั้นตอนนี้:

แผ่นตะกั่วแผ่นตะกั่ว16 sheets, 6 % antimony, 7 1/2 lb/sq ft

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
3

Hang and strap the lining

Dress the lead over the top angle to carry it. Hold it to the shell with straps of round-edged tire steel (Fig. 170: seven straps 2 1/2 x 3/8 in, about 9 ft long), no more than 8 ft apart round the shell; round edges won't cut the lead while it is dressed. Bolt the straps through the shell with 1/2 in bolts, heads countersunk inside.

วัสดุสำหรับขั้นตอนนี้:

เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน7 2 1/2 x 3/8 in, about 9 ft
สลักเกลียวหัวหกเหลี่ยม - เกรด 8.8สลักเกลียวหัวหกเหลี่ยม - เกรด 8.81 1/2 in, number not given

เครื่องมือที่ต้องใช้:

ค้อนไม้ค้อนไม้
4

Burn the seams and cover the straps

Burn (fuse) the lead seams together. Burn a narrow strip of lead over each strap onto the lining, so no steel or bolt head is left bare to the acid. Not given: the burning tool.

วัสดุสำหรับขั้นตอนนี้:

แผ่นตะกั่วแผ่นตะกั่ว1 cover strips

เครื่องมือที่ต้องใช้:

คบเพลิงคบเพลิง

วัสดุ

5

เครื่องมือที่จำเป็น

6

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...