ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Turning-Tub Churn: A Crank Spins the Tub on a Geared Pedestal Against Two Fixed Triangular Beaters Held From Standards
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
9
0
0
0
0

Turning-Tub Churn: A Crank Spins the Tub on a Geared Pedestal Against Two Fixed Triangular Beaters Held From Standards

M. C. Longacre of Cleveland, Ohio, received US 31,355, dated 5 February 1861, for a churn that turns the tub instead of the dasher. A crank and bevel gears hidden in a drum on the base spin a disk on which the tub, or a common pail, stands. Two triangular wooden beaters, each with a hole along it for air, hang still inside the tub from arms on two standards and can be set nearer the wall or deeper. The tub throws the cream outward and the beaters throw it back. The patent gives no sizes; every size here is ours.
ขั้นสูง
About 3 days

คำแนะนำ

1

How fast to turn the tub

กำลังโหลดสมุด Jupyter…
2

A turning vessel against a fixed break, a year and a half before

Harsha also turns the vessel against something fixed. Longacre stands the tub upright on a geared pedestal and makes the fixed beaters adjustable.
3

Read US 31,355

"Now, if the crank H is turned, the tub I, and disk D will receive a rotary motion, and the centrifugal force, tending to throw the fluid to the walls of the tub, the beaters at the same time tending to throw the same fluid back toward the center, the cream or milk has thus two forces constantly acting upon it, one a centrifugal, and the other a centripetal."
4

Base A, cylinder B and posts C

Glue up a hardwood base A 40 mm thick, a 400 mm circle with ends 120 mm wide running out to 700 mm overall. Cut a 30 mm slot 120 mm long along each end for the standards' feet. Roll a strip of 1.5 mm stainless sheet 168 mm wide into a cylinder B 310 mm across, rivet the lap, and screw it to the base through small tabs. Screw three hardwood posts C 40 mm square and 170 tall inside it, 110 mm from the centre and a third of a turn apart, the first at the back. Bore the cylinder 16.6 mm at the front, 97 mm up, for the crank shaft.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง3 ชิ้น
กาวไม้กาวไม้1 ชิ้น
แผ่นสเตนเลสแผ่นสเตนเลส1 ชิ้น
หมุดย้ำแบบดึงหมุดย้ำแบบดึง6 ชิ้น
สกรูไม้สกรูไม้16 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เข็มทิศเข็มทิศ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
เราเตอร์เราเตอร์
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ชุดปืนย้ำหมุดชุดปืนย้ำหมุด
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
แคลมป์แบบบาร์แคลมป์แบบบาร์
ชุดไขควงชุดไขควง
5

Print the cog wheel E'

The cog wheel E' on the spindle under the disk: 14 teeth, module 2.5, 16.2 mm bore, its hub up. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
6

Print the driving wheel G

The driving wheel G on the crank shaft: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
7

Step G, pipe box F, spindle E, gears and crank H

Bore the base's centre 8.4 mm and run an M8 bolt up through it with a nut each side, its head the step G, so it can be screwed up or down. Set a stainless tube F 30 mm long round it. Cut a 16 mm stainless spindle E 185 mm long; pin the cog wheel E' on it with its teeth 150 mm above the base. Screw a hardwood bearing block C' 40 x 25 x 120 mm to the base 55 to 80 mm in front of the centre, bored 16.6 mm across 97 mm up. Run a 16 mm stainless crank shaft 250 mm long through the cylinder and block, with the wheel G pinned on its inner end meshing E' from below and its end stopping clear of the spindle, a shaft collar against the block, and a crank H of mild steel flat bar, 100 mm throw, with a hardwood handle.

วัสดุสำหรับขั้นตอนนี้:

ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด1 ชิ้น
น็อตหกเหลี่ยมน็อตหกเหลี่ยม2 ชิ้น
ท่อสเตนเลสท่อสเตนเลส1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส2 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
Shaft CollarShaft Collar1 ชิ้น
สลักผ่าสลักผ่า3 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ประแจเลื่อนประแจเลื่อน
ชุดไขควงชุดไขควง
8

Disk D, flange D', bead H and tub I

Cut an 18 mm HDPE disk D 330 mm across, bore it 16.2 mm at the centre and fix it on the spindle's top. Screw under it a bead H, an HDPE ring 230 mm across outside and 210 inside, 2 mm thick, and on top a flange ring D' 300 mm across outside and 282 inside, 15 high, that the bucket's foot just drops into. Screw the step G up until the bead just touches the posts' tops. Use a 20-litre food-grade bucket as the tub I; for the patent's set screws J, two machine screws through the flange bearing on the bucket's foot.

วัสดุสำหรับขั้นตอนนี้:

แผ่น HDPEแผ่น HDPE2 ชิ้น
สกรูไม้สกรูไม้12 ชิ้น
ถังขนาด 20 ลิตรถังขนาด 20 ลิตร1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด2 ชิ้น

เครื่องมือที่ต้องใช้:

เข็มทิศเข็มทิศ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ประแจเลื่อนประแจเลื่อน
ชุดไขควงชุดไขควง
9

Beaters L, supports M, stems N, arms O, standards P and cover K

Plane two hardwood beaters L to a triangle 40 mm a side, 330 long, and bore a 10 mm hole through each lengthwise for air. Cut two hardwood supports M 50 x 40 x 65 mm with a triangular socket below for a beater's top and a 20 mm square socket above for a stem; glue the beaters in. Cut two hardwood stems N 20 mm square, 170 long, and fit each in its support. Make two standards P 40 x 40 mm, 650 tall, each on a foot Q 60 x 80 x 20 mm with a carriage bolt down through the base's slot and a wing nut Q' under it, so the standards slide in and out; let each stand in a socket in its foot (R) so it lifts out. Fix a hardwood arm O 30 mm square across the top of each standard, reaching in to its stem, with a 20 mm square hole and a wing-nut clamp bolt so the stem can be set higher or lower. Cut an HDPE cover K 304 mm across in two halves, notched for the stems.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง2 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สลักเกลียวหัวกลมสลักเกลียวหัวกลม4 ชิ้น
น็อตปีกผีเสื้อน็อตปีกผีเสื้อ4 ชิ้น
แหวนรองแบนแหวนรองแบน4 ชิ้น
แผ่น HDPEแผ่น HDPE1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
ชุดสิ่วไม้ชุดสิ่วไม้
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
ประแจเลื่อนประแจเลื่อน
ตลับเมตรตลับเมตร
10

The build in 3D

FreeCAD model of this build, the drum, disk and tub cut open: the base with its slotted ends, the drum, posts and bearing block, the step, spindle, cog wheel and driving wheel with the crank, the disk with its bead and flange, the bucket, and the two beaters hanging from their supports, stems, arms and standards.
ไฟล์แบบBLENDCC0 - Free
11

Churn

Set the bucket in the flange and pour in about 8 litres of heavy cream at about 15 °C, checked with the thermometer. Set the beaters close to the wall and reaching near the bottom without touching, and lay on the cover halves. Turn the crank steadily, timing it, not so fast that the cream climbs to the rim. When the butter comes, keep turning a little so it gathers in a mass. Lift off the cover and beaters, lift the bucket off the disk, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด8 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
12

Troubleshooting

Turning-tub churn troubleshooting.

Flow

Loading...
13

History and honest limits

**M. C. Longacre** of Cleveland, Cuyahoga County, Ohio, assignor to himself and R. R. Herrick, US 31,355, 5 February 1861, "Churn". He claimed "rotating the body of the churn in a vertical position by means of the disk (C) or its equivalent, when connected with the stationary dashers (L) arranged as described, for the purpose of adjusting the same both vertically and horizontally". His text uses the letters G and H each for two parts (the step and the driving wheel; the bead and the crank). His gears were bevel wheels; ours are a printed pinion and crown wheel, and our drum is stainless sheet. The patent gives no sizes; every size here is ours.

วัสดุ

22

เครื่องมือที่จำเป็น

22

ไฟล์ออกแบบ

3

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...