ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Rocking Twin-Dasher Lever Churn: One Lever Rocks the Box and Works Two Dashers Through a Perforated Wall
A. C. Stiles of South Bloomfield, Ohio, received US 3,764, dated 27 September 1844, for a rocking churn: an oblong box on rockers, split by a partition with holes, with a dasher on each side worked by arms on shafts across the ends, and one upright lever that rocks the box and works the dashers together.
This rung prints the partition, dashers and arms, builds the box and makes butter.
ขั้นสูง
About 6 hours, plus printing
คำแนะนำ
1
1
One lever, three motions
One lever, three motions
กำลังโหลดสมุด Jupyter…
2
2
Two dashers from one lever, before it
Two dashers from one lever, before it
Mitchell worked two dashers from one lever; Stiles adds rockers and a perforated partition between them.
3
3
Read US 3,764
Read US 3,764
"The machine is operated by moving the upright lever l, to and fro, which rocks the box, while at the same time it works the dashers up and down, thus throwing the cream through the partition d, till the butter is made."
4
4
Print the parts
Print the parts
Print the partition (/uploads/blueprints/rocking-twin-dasher-lever-churn-partition.stl), two dashers (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher.stl), two dasher arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-dasher-arm.stl) and two lower arms (/uploads/blueprints/rocking-twin-dasher-lever-churn-lower-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
วัสดุสำหรับขั้นตอนนี้:
เส้นใย PETG1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)5
5
Box on rockers
Box on rockers
Build a pine box about 260 × 120 × 150 mm with a close-fitting lid, sealed inside. Glue the partition across its middle and screw two curved pine rockers lengthwise underneath. Drill the lid for the two dasher handles.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้สน1 ชิ้น
กาวไม้1 ชิ้น
ตะปูเกลียวไม้ #8 x 1 นิ้ว1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยมือ
เลื่อยฉลุ
สว่านไร้สาย
ชุดดอกสว่าน
แคลมป์6
6
Shafts, arms and lever
Shafts, arms and lever
Set a 10 mm square shaft across each end on two studs, 60 mm above the lid. Fit a dasher arm on each, pointing inward and pinned to its dasher's handle, and a lower arm on each outside the box. Join the lower arms with a pine bar, and pivot an upright pine lever on a block near the box's foot, pinned to the bar's middle.
วัสดุสำหรับขั้นตอนนี้:
เดือยไม้เนื้อแข็ง1 ชิ้น
แผ่นไม้สน1 ชิ้น
แท่งเหล็กกลมคาร์บอนต่ำ1 ชิ้น
สกรูเกลียวมิล1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยมือ
สว่านไร้สาย
ชุดดอกสว่าน
ชุดไขควง7
7
The patent drawing
The patent drawing
US 3,764 drawing sheet, public domain (expired patent).

8
8
Rock and churn
Rock and churn
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Work the lever to and fro: the box rocks and the dashers rise and fall in turn. Keep fingers clear of the arms and the rockers. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด1500 มล.
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่9
9
Troubleshooting
Troubleshooting
Rocking twin-dasher churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**A. C. Stiles** of South Bloomfield, Pickaway County, Ohio, US 3,764, 27 September 1844. He claimed the combination of the rockers and dashers in the double-chambered churn. His drawing gives no sizes; ours are ours. FDM prints hold food in their layer lines, so wash well and replace when worn.
วัสดุ
11- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1500 มล.ตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
11- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้


