ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Tooled Leather Magazine Cover: Silk-Lined, With Strips to Hold the Magazine (Boy Mechanic, 1915)
Tex

สร้างโดย

Tex

13. พฤศจิกายน 2026FO
10
0
0
0
0

Tooled Leather Magazine Cover: Silk-Lined, With Strips to Hold the Magazine (Boy Mechanic, 1915)

Mary C. Scovel's magazine cover (The Boy Mechanic, Book 2, 1915): an 11 by 15 in sheet of calfskin with a tooled border design on the front, lined with heavy silk, and two silk strips inside into which the magazine's covers slip.
เริ่มต้น
About 4 hours

คำแนะนำ

1

Her sizes, and the design panel

กำลังโหลดสมุด Jupyter…
2

Read The Boy Mechanic, Book 2

Her outfit: "two special tools costing 50 cents each, one with a narrow edge for lining patterns, and one with broad ends for tooling; and a piece of tin, plate glass, or very smooth hard wood, which should not be smaller than 9 by 12 in. A soft sponge, a triangle, a rule, tracing paper and a hard pencil are also needed." Russian calfskin is best for tooling and stamping.
3

Damp the leather and transfer the design

Draw the whole design for the cover: a border design bounded by rectangular lines, 5-1/4 in wide, 1 in from the front edge, 1-1/2 in from the top and 2-1/4 in from the bottom (leather 11 by 15 in, narrow edges folded together) on tracing paper. Wet the leather on the wrong (unfinished) side with a soft sponge: pat it to moisten, not soak, it; too wet and the tool sticks and leaves an uneven background. Pin the design firmly on the leather, tack the leather down on its outer margin to the glass or board, and go over every line with a hard pencil, with firm, even pressure. Lift the paper and go over the lines with the narrow lining tool, with a strong, firm stroke. A line design can stop here.

วัสดุสำหรับขั้นตอนนี้:

หนังลูกวัวหนังลูกวัว1 ชิ้น

เครื่องมือที่ต้องใช้:

ฟองน้ำฟองน้ำ
กระดาษลอกลายกระดาษลอกลาย
ดินสอดินสอ
หมุดปักกระดาษ (กล่อง 50 ตัว)หมุดปักกระดาษ (กล่อง 50 ตัว)
แผ่นแก้วแผ่นแก้ว
เครื่องมือแกะลายหนังเครื่องมือแกะลายหนัง
4

Tool or stamp the background

Leave at least 1/8 in between the edge of the pattern and the design. To tool, press the background down with the broad end in even, long strokes; if it will not go down, the leather is too dry, so take it off and damp the back again. Keep the edges sharp between pressed and raised parts. To stamp instead, strike a small carpenter's nail set lightly with a wooden mallet in rows of circles; too hard a blow cuts the leather.

เครื่องมือที่ต้องใช้:

เครื่องมือแกะลายหนังเครื่องมือแกะลายหนัง
เหล็กส่งตะปูเหล็กส่งตะปู
ค้อนไม้ค้อนไม้
ฟองน้ำฟองน้ำ
5

Line and fit the strips

Line the inside with heavy silk, allowing 1/4 in to turn in on all four sides. Lay two strips of the lining, 2-1/2 in wide and 11 in long, 1-1/2 in from each side over the lining. Stitch lining, strips and leather together about 1/8 in from the edge all round. The magazine's covers slip between the cover and the strips. Stitch on a sewing machine with a long stitch, a large needle and silk as heavy as the needle takes; try it on a scrap first, and put tissue paper over the leather if the foot marks it. Without a machine, prick holes with an awl and sew with needle and silk, running or over-and-over; going over-and-over to the end and back gives an X stitch.

วัสดุสำหรับขั้นตอนนี้:

ผ้าไหมผ้าไหม1 ชิ้น
ด้ายไหมด้ายไหม1 ชิ้น

เครื่องมือที่ต้องใช้:

กรรไกรกรรไกร
ไม้บรรทัดไม้บรรทัด
จักรเย็บผ้าจักรเย็บผ้า
เหล็กหมาด (สว่านเจาะรูมือ)เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่มเข็มเย็บอานม้าสองเล่ม
6

Troubleshooting

Magazine cover troubleshooting.

Flow

Loading...
7

History and honest limits

From Mary C. Scovel, "Arts-Crafts Leather Work", in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 432-441), Part II. She does not give the leather; Russian calf is her choice for tooled work. The tools and metric figures are ours.

วัสดุ

3
  • ตัวยึดตำแหน่ง
  • 1 ชิ้น
    ตัวยึดตำแหน่ง
  • 1 ชิ้น
    ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

13

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...