ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Screwdriver: a Flat Blade Forged, Packed at a Low Heat and Tempered Grey (Holford, 1907)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
11
0
0
0
0

Screwdriver: a Flat Blade Forged, Packed at a Low Heat and Tempered Grey (Holford, 1907)

A flat screwdriver is a steel shank flattened to a blade that fits the slot of a screw. H. Holford's 20th Century Toolsmith and Steelworker (1907) says most smiths make them so they twist or break on a hard screw, and gives his cure: forge it from 75-point carbon steel, strike the blade a few good blows on each flat at a low heat, harden it and let the temper run to grey. His Fig. 60 shows the shape without its handle. He gives no sizes and no handle, which are unknown here; the brine bath is from his chapter on the hardening bath. Source: H. Holford (1907), pp. 21, 118. Picture: his Fig. 60.
ระดับกลาง
Half a day

คำแนะนำ

1

Read Holford

"Strike it a few good blows on each flat side of the screw driving edge while at a low heat. Then harden and allow the temper to draw to a grey, cool off and you will have a screw driver that will give unlimited satisfaction."
2

Forge the shape

Take good steel of 75 points carbon. Forge it to the shape of Fig. 60: a round shank, flattened at one end to the driving blade and drawn to a pointed tang at the other for the handle. Holford gives no sizes (unknown).

วัสดุสำหรับขั้นตอนนี้:

เหล็กเครื่องมือสี่เหลี่ยมจัตุรัสเหล็กเครื่องมือสี่เหลี่ยมจัตุรัส1 bar

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
ทั่งทั่ง
ค้อนช่างตีเหล็กค้อนช่างตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
แว่นนิรภัยแว่นนิรภัย
ถุงมือกันความร้อนถุงมือกันความร้อน
3

Pack the blade

At a low heat, strike a few good blows on each flat side of the driving edge.

เครื่องมือที่ต้องใช้:

ค้อนช่างตีเหล็กค้อนช่างตีเหล็ก
ทั่งทั่ง
เตาตีเหล็กเตาตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
4

Harden and temper grey

Heat the blade end evenly and quench it in the hardening bath. Holford's bath is clean water free from grease, best made into a brine with as much salt as the water will dissolve, kept as large and as cold as possible. Brighten the blade with a file so the colours show, draw the temper to a grey, then cool it off.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
น้ำเกลืออิ่มตัวน้ำเกลืออิ่มตัว
คีมช่างตีเหล็กคีมช่างตีเหล็ก
ตะไบเนื้อละเอียดตะไบเนื้อละเอียด
ถุงมือกันความร้อนถุงมือกันความร้อน
5

Fit a handle

Fit a handle on the tang. Holford shows the screwdriver without one and does not say what it is made of (unknown).

วัสดุสำหรับขั้นตอนนี้:

วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ1 handle
6

History and honest limits

Holford, a toolsmith writing for blacksmiths and tool dressers, says a good screwdriver is prized by every mechanic, woodworkers most of all, yet few smiths could make one that would not break or twist. His temper table lists the screwdriver at grey, in 0.75 carbon steel. He gives no sizes, no handle and no heat for hardening; those are unknown here, and the tools are ours.

วัสดุ

2

เครื่องมือที่จำเป็น

9

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...