การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)
Bubbles

สร้างโดย

Bubbles

14. พฤศจิกายน 2026IT
6
0
0
0
0

Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)

Alfred Soward's lampwork bulb pipette from Amateur Work (1886), made like his thistle funnel: a 3/8 in. bore tube closed and drawn down onto a 1/8 in. stem, blown into a bulb, a thin second bulb blown and broken off the far side to leave a short neck, and a second stem drawn to a fine capillary tip joined on.
ขั้นสูง
An hour once the basic operations are mastered

คำแนะนำ

1

Read Soward

"To make a pipette the process is very similar." (to the thistle funnel)
2

Prepare the tubes

Take glass tube of about 1/8 in. (3 mm) bore for the stems and about 3/8 in. (10 mm) bore for the bulb. Close the wide tube at one end in the form of his fig. 41 A, then soften it about an inch from the end and draw it down to the small tube's diameter.

วัสดุสำหรับขั้นตอนนี้:

หลอดแก้วหลอดแก้ว1 ชิ้น

เครื่องมือที่ต้องใช้:

ตะเกียงบุนเซนตะเกียงบุนเซน
ท่อเป่าแก้วท่อเป่าแก้ว
3

Join the first stem

Cut the drawn, flask-shaped piece off with a file and fuse it to a length of the narrow tube: soften both ends, press them together, pull gently to reduce the thickened joint, and blow a gentle stream of air in.

วัสดุสำหรับขั้นตอนนี้:

หลอดแก้วหลอดแก้ว1 ชิ้น

เครื่องมือที่ต้องใช้:

ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ตะเกียงบุนเซนตะเกียงบุนเซน
ท่อเป่าแก้วท่อเป่าแก้ว
4

Blow the bulb

Soften the flask part and blow it into a bulb through the stem.

เครื่องมือที่ต้องใช้:

ตะเกียงบุนเซนตะเกียงบุนเซน
ท่อเป่าแก้วท่อเป่าแก้ว
5

Open the far end

Play the flame on the point opposite the stem (A in fig. 41) and blow a very thin second bulb with a strong blast. Break it away: it leaves a small projecting tube (B).

เครื่องมือที่ต้องใช้:

ตะเกียงบุนเซนตะเกียงบุนเซน
ท่อเป่าแก้วท่อเป่าแก้ว
6

Draw and join the tip

Draw a second piece of narrow tube to a capillary end: thicken it in the flame, pull the hands apart, cut with a file and hold the cut end a moment in the flame. Join this stem to the projecting tube as before.

วัสดุสำหรับขั้นตอนนี้:

หลอดแก้วหลอดแก้ว1 ชิ้น

เครื่องมือที่ต้องใช้:

ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ตะเกียงบุนเซนตะเกียงบุนเซน
ท่อเป่าแก้วท่อเป่าแก้ว
7

Troubleshooting

Pipette troubleshooting.

Flow

Loading...
8

History and honest limits

From Alfred W. Soward, "Glass-Blowing for Amateurs" IV, **Amateur Work, Illustrated**, vol. V (1886), pp. 173-176, figs. 39-41 (checked on the archive.org scan amateurworkillus05lond). He gives no volume or graduation: calibrate it by weighing water if you need one (see the graduated-pipette blueprint). Metric figures are ours.

วัสดุ

1
  • ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

3

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...