การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)
Forge

สร้างโดย

Forge

15. พฤศจิกายน 2026NO
5
0
0
0
0

Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)

Alfred Soward's laboratory cork-borer from Amateur Work (1881): about 4 in. of brass tube the size of the hole, one end filed on the outside to a ring-shaped cutting edge, a brass flange on the other end to strengthen it, and a steel wire pushed through a cross hole as a handle. Turned like a gimlet, it cuts a clean, centred hole for a glass tube.
เริ่มต้น
An hour

คำแนะนำ

1

Read Soward

"This latter instrument is simply a piece of brass tube about 4 in. long, and of a diameter suited to the hole required."
2

Cut the tube

Cut about 4 in. (100 mm) of brass tube whose outside diameter matches the hole you need (he takes 3/8 in., about 10 mm, for a glass tube). Square both ends.

วัสดุสำหรับขั้นตอนนี้:

ท่อทองเหลืองท่อทองเหลือง1 ชิ้น

เครื่องมือที่ต้องใช้:

ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
3

File the cutting edge

File one end on the outside only, all round, to a thin cutting edge: like two gouges put together with their hollow sides facing (B in his fig. 7). Leave the bore untouched.

เครื่องมือที่ต้องใช้:

ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ตะไบเข็มตะไบเข็ม
4

Fit the flange

Fit a small brass ring or flange round the other end to strengthen it (D in fig. 7). Ours: cut it from brass sheet and soft-solder it on.

วัสดุสำหรับขั้นตอนนี้:

แผ่นทองเหลืองแผ่นทองเหลือง1 ชิ้น
ลวดตะกั่วบัดกรีลวดตะกั่วบัดกรี1 ชิ้น
ฟลักซ์ฟลักซ์1 ชิ้น

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
หัวแร้งบัดกรีหัวแร้งบัดกรี
5

Cross hole and handle

Below the flange, drill a hole straight across the tube for a piece of steel wire. Push the wire through so it stands at right angles to the tube as a handle (C in fig. 7, drawn with a head on one end).

วัสดุสำหรับขั้นตอนนี้:

ลวดเหล็กลวดเหล็ก1 ชิ้น

เครื่องมือที่ต้องใช้:

สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
6

Troubleshooting

Cork borer troubleshooting.

Flow

Loading...
7

History and honest limits

From Alfred W. Soward, "Filters: Their Construction and Maintenance" I, **Amateur Work, Illustrated**, vol. I (1881), pp. 131-133 and fig. 7 (checked on the archive.org scan amateurworkillus11881lond). To use it, hold the cork's small end against a wall or the bench edge, press on the centre of the large end and turn like a gimlet, giving the cork a quarter turn left after each quarter turn of the borer right. A bought set of four then cost 1s. He does not say how the flange is fixed: soft solder, the metric figures and the tools are ours.

วัสดุ

5

เครื่องมือที่จำเป็น

8

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...