การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Ore Crushing Rolls: Hard Shells on Soft Iron Cores, One Roll in Spring-Loaded Boxes, Gap Set by Shims (Richards, Ore Dressing, 1903)
Forge

สร้างโดย

Forge

15. พฤศจิกายน 2026NO
5
0
0
0
0

Ore Crushing Rolls: Hard Shells on Soft Iron Cores, One Roll in Spring-Loaded Boxes, Gap Set by Shims (Richards, Ore Dressing, 1903)

The crushing rolls that took ore from the jaw breaker in a 1900s mill, as Robert Richards described them: two shafts on one cast-iron frame, each carrying a soft-iron core with a replaceable hard shell; one runs in fixed boxes, the other in movable boxes pushed toward it by a nest of steel springs that yields like a safety valve; shims set the gap. Little fines, ideal for soft brittle ores.
ขั้นสูง
Weeks (castings and machining)

คำแนะนำ

1

His figures

กำลังโหลดสมุด Jupyter…
2

Read Richards

"The ore is therefore broken by compression."
3

Frame and shafts

Cast the frame as one piece, both sides joined by end pieces, so settling of the building can't throw the shafts out of line (make it in two parts only if it must travel by mule). Turn two shafts of mild steel or wrought iron, each on two bearings.

วัสดุสำหรับขั้นตอนนี้:

ชิ้นงานเหล็กหล่อชิ้นงานเหล็กหล่อ1 ชิ้น
เพลาเหล็กกล้าเพลาเหล็กกล้า1 ชิ้น

เครื่องมือที่ต้องใช้:

กระบวยเทน้ำโลหะกระบวยเทน้ำโลหะ
เครื่องกลึงโลหะเครื่องกลึงโลหะ
รอกพวงรอกพวง
4

Cores and shells

Force a soft cast-iron core onto each shaft. Krom's way (Fig. 37): two slightly conical half-cores, one shrunk on for good, the other split on one side and drawn in by four draw bolts; half-cores no wider than 4-5 in. Cast hard shells 2-5½ in. thick (chilled iron or steel), with wrought-iron staves cast in if chilled so the slightly conical inside can be turned to fit; turn the face true.

วัสดุสำหรับขั้นตอนนี้:

ชิ้นงานเหล็กหล่อชิ้นงานเหล็กหล่อ1 ชิ้น
แท่งเหล็กดัดแท่งเหล็กดัด1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
กระบวยเทน้ำโลหะกระบวยเทน้ำโลหะ
5

Boxes, springs and shims

Mount one shaft in fixed boxes and the other in movable ones, both babbitted, with shields and a cotton-waste groove against grit. Put a nest of steel spiral springs outside the fixed pillow block, with bolts carrying the force to the movable box, equal on both sides, compressed between plates by two compression bolts. Set the gap with shims and keep them in: the springs should only give when a hard lump comes through.

วัสดุสำหรับขั้นตอนนี้:

Coil SpringCoil Spring1 ชิ้น
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด1 ชิ้น
ชิ้นงานเหล็กหล่อชิ้นงานเหล็กหล่อ1 ชิ้น

เครื่องมือที่ต้องใช้:

ชุดประแจปากตายชุดประแจปากตาย
เครื่องกลึงโลหะเครื่องกลึงโลหะ
6

Drive and run

Drive by belt and pulley (or gears and pulleys for slow coarse work). Feed lumps no bigger than about 1½ in. (4 cm), 2½ in. at most, evenly with a feeder so a rush of ore does not choke it.

วัสดุสำหรับขั้นตอนนี้:

รอกรอก1 ชิ้น
สายพานขับสายพานขับ1 ชิ้น

เครื่องมือที่ต้องใช้:

ชุดประแจปากตายชุดประแจปากตาย
7

Troubleshooting

Crushing rolls troubleshooting.

Flow

Loading...
8

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter III, §§ 71-85, pp. 62-74, Fig. 37 and Tables 34-39 (checked on the archive.org scan oredressing01richuoft; p. 62 from its text layer). Rubber springs were the cheap short-life option; levers and weights had nearly gone out of use. Richards surveys machines from many makers rather than one design: building from castings, the size and metric are ours, and the babbitt alloy has no head yet.

วัสดุ

8

เครื่องมือที่จำเป็น

4

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...