การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Stamp Mill: California Five-Stamp Battery (Richards, Ore Dressing 1903)
Forge

สร้างโดย

Forge

3. พฤศจิกายน 2026NO
16
0
0
0
0

Stamp Mill: California Five-Stamp Battery (Richards, Ore Dressing 1903)

The gravity stamp mill: five heavy iron stamps stand in a cast-iron mortar on a timber block. Cams on a turning shaft lift each stamp by its tappet and let it fall by its own weight onto the ore on a die. Water washes the crushed ore out through a screen. Result: a stamp battery that pounds ore to sand, at 80 to 110 drops a minute. Source: R. H. Richards, Ore Dressing, vol. I (1903), Chapter V, Gravity Stamps. Unknown: one complete set of sizes; Richards gives the range found in the mills. Picture: Fig. 90 of the book.
ขั้นสูง
Unknown

คำแนะนำ

1

Dig and level the foundation

Dig a trench in gravel, or blast one in rock, about 2 feet longer than the mortar block at each end and about 2 feet wider at each side. Level the bottom with tamped concrete, sand or clay. Concrete should be at least 30 inches thick, or it may crumble. Two layers of 2-inch plank spiked together may go on top.

วัสดุสำหรับขั้นตอนนี้:

คอนกรีตคอนกรีต1 levelling layer
แผ่นไม้แปรรูปแผ่นไม้แปรรูป1 two layers of 2-inch plank

เครื่องมือที่ต้องใช้:

พลั่วพลั่ว
ค้อนค้อน
2

Stand the mortar block

Stand timbers or planks on end in the trench as the mortar block, sized for one five-stamp mortar. The mills used everything from 30 x 30 inch squared timbers to 2 x 12 inch planks bolted together. Set vertical bolts 3 to 4 feet long into the block to hold the mortar down. Not given: the bolts' metal.

วัสดุสำหรับขั้นตอนนี้:

ไม้แปรรูปหน้าตัดสี่เหลี่ยมไม้แปรรูปหน้าตัดสี่เหลี่ยม1 mortar block
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 hold-down bolts

เครื่องมือที่ต้องใช้:

ชุดประแจปากตายชุดประแจปากตาย
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
3

Build the frame

On mud sills and cross sills, stand the posts (end posts 12 x 24 inches in most mills) with buckstaves, a platform, and lower and upper guide timbers. The guides keep the stamp stems vertical. Fit finger bars on a jack shaft between the posts, so each stamp can be propped up under its tappet. The frame carries the cam shaft and the drive.

วัสดุสำหรับขั้นตอนนี้:

ไม้แปรรูปหน้าตัดสี่เหลี่ยมไม้แปรรูปหน้าตัดสี่เหลี่ยม1 sills, posts, guide timbers, platform
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 bolts and jack shaft

เครื่องมือที่ต้องใช้:

ชุดประแจปากตายชุดประแจปากตาย
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
4

Set the mortar, dies and screen

Bed the cast-iron mortar on tarred blankets or sheet rubber on the mortar block, for an even bearing, and bolt it down. Put the dies in its bottom: cylinders on square foot plates that fill the floor of the mortar. Mount a screen of punched Russia sheet iron in a wooden frame over the opening in front.

วัสดุสำหรับขั้นตอนนี้:

ชิ้นงานเหล็กหล่อชิ้นงานเหล็กหล่อ1 mortar and five dies
แผ่นยางธรรมชาติแผ่นยางธรรมชาติ1 packing
แผ่นเหล็กรัสเซียแผ่นเหล็กรัสเซีย1 screen

เครื่องมือที่ต้องใช้:

ชุดประแจปากตายชุดประแจปากตาย
5

Make the five stamps

Each stamp has four parts. The shoe is chilled cast iron, its butt cast in heavy chills and its shank in sand. The boss is tough cast iron, the shoe's diameter and often 18 inches long, with sockets for the shoe shank and the stem and two keyways for knock-out wedges. The stem is solid wrought iron or mild steel, turned true and tapered at both ends so it can be reversed. The tappet is cast iron, with a flange above and below, locked on the stem by a gib and keys. Put the extra weight in the boss. Louis designs for 11 to 14 pounds of stamp per square inch of die; the mills used stamps of 650 to 1,100 pounds.

วัสดุสำหรับขั้นตอนนี้:

ชิ้นงานเหล็กหล่อชิ้นงานเหล็กหล่อ1 shoes, bosses, tappets
แท่งเหล็กดัดแท่งเหล็กดัด1 stems, gibs, keys

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
6

Fit the cam shaft and drive

Turn a wrought-iron or steel cam shaft true, with a key seat, and key on five cams. Each cam usually has two arms with spiral lifting faces, cast iron with chilled faces or cast steel. Drive the shaft by a rubber belt from the main shaft, over a pulley of wood built on a cast-iron hub and flanges, with a tightener. Not given: the engine or wheel that turns the main shaft.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กดัดแท่งเหล็กดัด1 cam shaft
ชิ้นงานเหล็กหล่อชิ้นงานเหล็กหล่อ1 cams, pulley hub and flanges
แผ่นไม้แปรรูปแผ่นไม้แปรรูป1 pulley rim
สายพานขับสายพานขับ1 rubber belt

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ชุดประแจปากตายชุดประแจปากตาย
7

Add the water and the feed

Run one or two 1-inch water pipes into the back of the mortar, each with a plug cock that stays where it is set. Feed ore from the bin by a chute to an automatic feeder. One stamp trips the feeder when the ore layer on its die gets too thin, and a hand screw adjusts the point where it trips. Ore can also be fed by hand with a shovel.

วัสดุสำหรับขั้นตอนนี้:

ท่อน้ำท่อน้ำ1 water pipes
วาล์วที่ไม่ทราบวาล์วที่ไม่ทราบ1 plug cocks
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 feeder and chute

เครื่องมือที่ต้องใช้:

ชุดประแจปากตายชุดประแจปากตาย
พลั่วพลั่ว
8

Set up each stamp

Lay a 3-inch plank on the dies and set the bosses on it. Lower the stems into them and tap each stem down with a hammer, a board guarding its top, then drop it a few times at a very low drop. Hoist the stamp, put the shoe in place with wooden staves around its shank, and drop it on the plank to drive the shoe home; the staves swell when wet and hold it. Swap the plank for a block as high as the drop. Slip the tappet on, turn the cam until the tappet rests on its point, drive the keys home and drop the stamp gently a few times.

วัสดุสำหรับขั้นตอนนี้:

ลิ่มไม้ลิ่มไม้1 staves

เครื่องมือที่ต้องใช้:

แผ่นไม้แปรรูปแผ่นไม้แปรรูป
ค้อนค้อน
รอกพวงรอกพวง
9

Run the battery

Drop the stamps in order 1, 3, 5, 2, 4 (numbered from the left, standing behind the battery), so no two neighbours fall one after the other. The California practice is 80 to 110 drops a minute with a 5 to 9 inch drop. The cams turn the stamps as they lift, which evens out wear on shoes and dies. Lubricate the cams; soft soap with graphite is best. As shoes and dies wear, reset the tappets to restore the drop, and keep the height of discharge, from die to screen, the same.

เครื่องมือที่ต้องใช้:

ผงแกรไฟต์ผงแกรไฟต์
วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ
ชุดประแจปากตายชุดประแจปากตาย

วัสดุ

12

เครื่องมือที่จำเป็น

10

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...