ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Stone Carving Chisels: Mallet-Headed Plain and Tooth Chisels and Points for Soft Stone (Holford, 1907)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
13
0
0
0
0

Stone Carving Chisels: Mallet-Headed Plain and Tooth Chisels and Points for Soft Stone (Holford, 1907)

Soft stone such as limestone and sandstone is cut with chisels struck by a wooden mallet, so their heads are broad and a little rounded. H. Holford's 20th Century Toolsmith and Steelworker (1907) shows a set: plain chisels, tooth chisels with a row of sharp teeth, and points, forged from 3/4 inch octagon steel of 75 points carbon and tempered a very pale blue. He gives no lengths, widths or tooth spacing; those are unknown here. The brine bath is from his chapter on the hardening bath. Source: H. Holford (1907), pp. 21, 131-133, 140-141. Picture: his Fig. 71.
ระดับกลาง
A day for a set

คำแนะนำ

1

Read Holford

"In cutting soft stone of any description wooden mallets are used, consequently the heads of the tools are made broad and a little rounding, so as not to cut or bruise the mallet."
2

Forge the mallet heads

Use 3/4 inch octagon steel of 75 points carbon. For each tool, upset the head end a little, fuller it in, draw it out, then swage it to its broad, slightly rounded shape between top and bottom swages (Fig. 78). For a narrow chisel, forge the head first; for a wide one, forge the cutting end first. Sizes are not given (unknown).

วัสดุสำหรับขั้นตอนนี้:

เหล็กเครื่องมือแปดเหลี่ยมเหล็กเครื่องมือแปดเหลี่ยม1 3/4 in octagon

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
ทั่งทั่ง
ค้อนช่างตีเหล็กค้อนช่างตีเหล็ก
เลื่อนลากเลื่อนลาก
ฟุลเลอร์ (เหล็กเซาะร่อง)ฟุลเลอร์ (เหล็กเซาะร่อง)
สเวจบนและล่างสเวจบนและล่าง
คีมช่างตีเหล็กคีมช่างตีเหล็ก
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
แว่นนิรภัยแว่นนิรภัย
ถุงมือกันความร้อนถุงมือกันความร้อน
3

Forge the chisels and points

For a wide chisel, upset the end to the width of the chisel before drawing it down to a thin cutting edge. Hammer the flat surfaces. Draw the points down to almost a square point (Fig. 72). For tooth chisels, punch the teeth into the edge in a punch machine after the flat surfaces have been hammered, then file each tooth to an extremely sharp point.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
ทั่งทั่ง
ค้อนช่างตีเหล็กค้อนช่างตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
เครื่องปั๊มเจาะเครื่องปั๊มเจาะ
ตะไบเนื้อละเอียดตะไบเนื้อละเอียด
4

Harden the chisels

Heat the cutting edge very evenly along its whole length and dip it at least one inch into the hardening bath (clean water, best as a strong brine, kept large and cold). Polish it bright by rubbing it across a board spread with fine clean sand near the forge, and draw the temper to a very pale blue, the right temper for all limestone tools.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
น้ำเกลืออิ่มตัวน้ำเกลืออิ่มตัว
แผ่นกระดานแผ่นกระดาน
ทรายละเอียดทรายละเอียด
คีมช่างตีเหล็กคีมช่างตีเหล็ก
ถุงมือกันความร้อนถุงมือกันความร้อน
5

Harden the points

Dip the points deep into the bath. Draw the temper so it shows at least 5/8 inch back from the point; if it runs so fast that only the very tip is tempered, the point bends and breaks easily.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
น้ำเกลืออิ่มตัวน้ำเกลืออิ่มตัว
แผ่นกระดานแผ่นกระดาน
ทรายละเอียดทรายละเอียด
คีมช่างตีเหล็กคีมช่างตีเหล็ก
ถุงมือกันความร้อนถุงมือกันความร้อน
6

History and honest limits

Holford sets the soft-stone tools apart from those for granite and marble: soft stone takes wooden mallets, hence the broad heads, and a very pale blue temper. The finest stone carvers' tools, struck only lightly, he hardens without drawing any temper at all. He gives no lengths, widths or tooth spacing; the tools used to make them are ours.

วัสดุ

1

เครื่องมือที่จำเป็น

15

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...