การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)
Woody

สร้างโดย

Woody

13. พฤศจิกายน 2026NO
6
0
0
0
0

Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)

Stillman Taylor's skis from The Boy Mechanic, Book 3 (1919): "far easier than snowshoe construction, since each runner is made from a single piece of plank". Ash or hickory is cut to his 8 ft pattern, thinned from the top only, the tips steamed to a 6 in bend, a centre groove cut, and the skis oiled and waxed.
ระดับกลาง
About 1 week

คำแนะนำ

1

Fig. 5 in centimetres, and the wax

กำลังโหลดสมุด Jupyter…
2

Read The Boy Mechanic, Book 3

"Either hickory or ash will give satisfaction, because both are heavy woods, as well as strong and flexible." For a man of good height, 7 to 8 ft is the right length.
3

Get and choose the wood

Get two ash or hickory planks about 9 ft long and 2 in thick, from the outside of the lower trunk, with the grain running as in his Fig. 6, A/D (in ash choose open, widely spaced grain). Or split a sound, straight tree about 10 in across and clear of knots for 10 ft: axe a straight groove about 1 in deep along each side and drive small wood wedges along it; hew only enough off the outside to make the flat running surface.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง2 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
ตลับเมตรตลับเมตร
4

Lay out and saw

Make a paper pattern from his Fig. 5 (8 ft ski): 3-3/8 in wide at the heel, 3-1/8 in at the foot, 4 in at the bend, rounding to the toe. Trace it on the plank and saw out; on green wood make the width about 1/4 in greater for shrinkage.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น

เครื่องมือที่ต้องใช้:

ดินสอดินสอ
เลื่อยมือเลื่อยมือ
ตลับเมตรตลับเมตร
5

Plane to thickness

Plane the running surface perfectly smooth, grain straight from point to heel. Work the thickness down from the top side only, never the bottom: about 1/2 in at the heel, 3/4 in at the foot and 1/2 in at the bend.

เครื่องมือที่ต้องใช้:

กบไสไม้กบไสไม้
กบสองมือจับกบสองมือจับ
6

Steam the tip

Lay the ski over a wash boiler of boiling water and soak the tip by mopping it with the water on a cloth tied to a stick. Bend gradually over many treatments to a good 6 in bend (it finishes near 5 in, as the wood straightens a little as it dries). Hold it in a rough frame over a short log, or lash or cleat the tips to the bench, as in his Fig. 7. The arch under the foot is easily put in, and easily straightened when cold if overdone.

เครื่องมือที่ต้องใช้:

หม้อใบใหญ่หม้อใบใหญ่
ไม้ถูพื้นไม้ถูพื้น
แคลมป์แบบบาร์แคลมป์แบบบาร์
7

Binding hole, balance and groove

Put in the hole for the foot binding. If the wood was left long, trim the heel so the ski balances when lifted by the toe straps (he sees no advantage in weighting a light heel with lead). Cut a groove in the exact centre of the running surface, about 1/8 in deep and 3/8 to 1/2 in wide, from the heel to the start of the bend, with a grooving plane or a small gouge.

วัสดุสำหรับขั้นตอนนี้:

สายหนังสายหนัง2 ชิ้น

เครื่องมือที่ต้องใช้:

สว่านมือสว่านมือ
สิ่วสิ่ว
สิ่วหน้าโค้งสิ่วหน้าโค้ง
เลื่อยมือเลื่อยมือ
8

Finish and wax

Sandpaper top and bottom and rub down with linseed oil with a little paraffin or beeswax in it; oil and wax the running surface (spar varnish on the tops if you want gloss). For a hard wax, melt 10 oz of beeswax with 5 oz of rosin, stir in 1 oz of turpentine and pour into small boxes. Rub it on and go over it with a hot flatiron; too much wax makes climbing hard.

วัสดุสำหรับขั้นตอนนี้:

กระดาษทรายกระดาษทราย1 ชิ้น
น้ำมันลินสีดน้ำมันลินสีด1 ชิ้น
ขี้ผึ้งพาราฟินขี้ผึ้งพาราฟิน1 ชิ้น
ขี้ผึ้งขี้ผึ้ง1 ชิ้น
ยางสนโรซินยางสนโรซิน1 ชิ้น
น้ำมันสนน้ำมันสน1 ชิ้น

เครื่องมือที่ต้องใช้:

หม้อใบใหญ่หม้อใบใหญ่
เตารีดเหล็กเตารีดเหล็ก
แปรงทาสีหน้ากว้างแปรงทาสีหน้ากว้าง
9

Troubleshooting

Ski troubleshooting.

Flow

Loading...
10

History and honest limits

From "How to Make Skis" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 27-30). His text gives the groove as 3/8 to 1/2 in wide; Fig. 5 shows 3/8 in. He does not describe the binding. The tools and metric figures are ours.

วัสดุ

8

เครื่องมือที่จำเป็น

13
  • ตัวยึดตำแหน่ง
  • 1 vendor sell this, none ship to you yet
    ตัวยึดตำแหน่ง
  • 1 vendor sell this, none ship to you yet
    ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...