การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)
Forge

สร้างโดย

Forge

14. พฤศจิกายน 2026NO
8
0
0
0
0

Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)

The marking scriber Richard Thompson made for his surface gauge in Amateur Work: 1/8 in. steel or a worn-out saw file, drilled in the middle, pointed at both ends with one end bent, annealed by burying it red-hot in lime, filed round while turned in a grooved hardwood block, and the points hardened.
เริ่มต้น
Two hours

คำแนะนำ

1

Read Thompson

"A worn-out saw file will answer very well, with a hole drilled through the centre to fit the bolt and pointed at each end, one of which is bent."
2

Rough the shape

Forge a flat piece of steel about 1/8 in. (3 mm) thick, or a worn-out saw file, roughly to shape: pointed at both ends, one end bent into a short hook (his fig. 30).

วัสดุสำหรับขั้นตอนนี้:

แผ่นแบนเหล็กกล้าเครื่องมือแผ่นแบนเหล็กกล้าเครื่องมือ1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
คีมช่างตีเหล็กคีมช่างตีเหล็ก
3

Anneal in lime

Heat it gently to a dull red and bury it in lime to cool slowly: it is then easy to file.

วัสดุสำหรับขั้นตอนนี้:

ปูนขาว (แคลเซียมไฮดรอกไซด์)ปูนขาว (แคลเซียมไฮดรอกไซด์)1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
4

Drill and flatten

Drill a hole through the middle to fit the mounting bolt and file the flat part to an even thickness for about 1/2 in. each side of the hole.

เครื่องมือที่ต้องใช้:

สว่านแท่นสว่านแท่น
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
5

File it round

Cut a groove along the end of a hardwood block about 3 x 2 x 1/2 in., held end up in the vice. Lay the scriber in the groove, turn it slowly toward you with the left hand and file it round with the right. File the points quite sharp.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
6

Harden the points

Harden the points (he gives no method; ours: heat the tips to a bright red and quench in water), then touch them up on an oilstone.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ถังชุบน้ำถังชุบน้ำ
หินลับมีดหินลับมีด
7

Troubleshooting

Scriber troubleshooting.

Flow

Loading...
8

History and honest limits

From Richard Thompson, "How to Construct a Compound Microscope" III, **Amateur Work, Illustrated**, vol. III, p. 198 and fig. 30 (checked on the archive.org scan amateurworkillus03lond). He mounts the scriber on a mahogany surface gauge with three brass washers 3/4 in. across and 1/16 in. thick. The hardening method, metric figures and tools are ours.

วัสดุ

3

เครื่องมือที่จำเป็น

10

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...