การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
8
0
0
0
0

Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)

William A. Tomlinson and Howell B. Bearden of Phoenix, Arizona, received US 1,813,783, dated 7 July 1931, for a table that turns any portable power saw into a table saw. The saw is clamped upside down on a carriage, its blade through the slot of a top hinged at the rear. The carriage rolls on ball-bearing rollers inside two steel tubes slotted along their undersides. A pedal pushes it forward through the work, leaving both hands free, and a spring brings it back. With the pedal left alone it works as a fixed saw, and the saw unbolts for hand use. The patent gives no sizes; every size here is ours.
ขั้นสูง
About 4 days

คำแนะนำ

1

Pedal, link and travel

กำลังโหลดสมุด Jupyter…
2

Read US 1,813,783

"By using the pedal in the manner above set forth both hands of the operator will be free for manipulating the work, which is especially desirable when pattern work is to be sawed."
3

Angle-iron frame

Bolt a frame of steel angle 900 x 500 mm, 850 high: four corner legs 1, side and end bars 2, 3 halfway up and 4, 5 at the top, flat-bar diagonal braces 6 at the top corners, a cross bar 7 between the rear legs above the middle bars, and a cross bar 8 between the front legs at the bottom. Drill a vertical row of 9 mm holes 13, 25 mm apart, near the top of each leg, for the track hangers.

วัสดุสำหรับขั้นตอนนี้:

เหล็กฉากเหล็กกล้าละมุนเหล็กฉากเหล็กกล้าละมุน6 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด40 ชิ้น
น็อตหกเหลี่ยมน็อตหกเหลี่ยม40 ชิ้น
แหวนรองแบนแหวนรองแบน40 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
เครื่องเจียรมุมเครื่องเจียรมุม
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
ฉากรวมอเนกประสงค์ฉากรวมอเนกประสงค์
ตลับเมตรตลับเมตร
ประแจเลื่อนประแจเลื่อน
แว่นนิรภัยแว่นนิรภัย
4

Slotted tube tracks

Cut two 900 mm lengths of 42 mm steel tube 9, 10 and cut a 10 mm slot 14 along the underside of each, stopping 20 mm short of the ends; file the slot's edges smooth. Bolt a flat-bar hanger 11 to each end of each tube and hang the tubes along the frame's sides from the legs with bolts 12 through the row of holes, at the height that suits your saw. Put a short coil spring 39 in each end of each tube as a buffer.

วัสดุสำหรับขั้นตอนนี้:

ท่อกลมเหล็กกล้าละมุนท่อกลมเหล็กกล้าละมุน2 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
Coil SpringCoil Spring4 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด8 ชิ้น
น็อตหกเหลี่ยมน็อตหกเหลี่ยม8 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
เครื่องเจียรมุมเครื่องเจียรมุม
ชุดตะไบชุดตะไบ
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
ประแจเลื่อนประแจเลื่อน
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
แว่นนิรภัยแว่นนิรภัย
5

Carriage and rollers

Cut the carriage 30 from 5 mm steel plate, as wide as between the tubes. At each corner bolt an upright flat-bar standard 31 that reaches up through a tube's slot, and on its top a short bar 33 across inside the tube carrying a 22 mm ball bearing 32 at each end on an M8 bolt with a lock nut. Slide the rollers into the tubes from the ends, the standards hanging down through the slots, and bolt them to the carriage.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
ตลับลูกปืนตลับลูกปืน8 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด16 ชิ้น
นอตล็อกไนลอนนอตล็อกไนลอน8 ชิ้น
แหวนรองแบนแหวนรองแบน16 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
เครื่องเจียรมุมเครื่องเจียรมุม
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
ชุดตะไบชุดตะไบ
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ประแจเลื่อนประแจเลื่อน
6

Pedal and springs

Pivot a lever 21 of steel flat bar on the front bottom cross bar 8, with an arm 22 to the side carrying the pedal 20 and a brace 23 from arm to lever. Join the lever's top to the carriage's front with a flat-bar link 24. Hook a return spring 25a from the rear cross bar 7 to the lever partway up.

วัสดุสำหรับขั้นตอนนี้:

เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน2 ชิ้น
เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน1 ชิ้น
สปริงดึงสปริงดึง1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด4 ชิ้น
นอตล็อกไนลอนนอตล็อกไนลอน4 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ประแจเลื่อนประแจเลื่อน
7

Mount the saw and the top

Turn the circular saw upside down on the carriage and bolt it by its base plate with bolts and wing nuts, so it lifts off for hand use; his T-bolt 34 and hook bolts 36 gripped the saw's handles, which modern saws do not suit. Make the top 42 of plywood on a steel angle frame 44, slotted along the blade's path, and hinge its rear edge to the frame so it swings up to reach the saw. Fit a catch 47 to lock it down and a folding flat-bar brace 49 to prop it up.

วัสดุสำหรับขั้นตอนนี้:

เลื่อยวงเดือนเลื่อยวงเดือน1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด4 ชิ้น
น็อตปีกผีเสื้อน็อตปีกผีเสื้อ4 ชิ้น
แผ่นไม้อัดแผ่นไม้อัด1 ชิ้น
เหล็กฉากเหล็กกล้าละมุนเหล็กฉากเหล็กกล้าละมุน1 ชิ้น
บานพับประตูบานพับประตู2 ชิ้น
ตะขอและห่วงติดเสื้อผ้าตะขอและห่วงติดเสื้อผ้า1 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
สกรูไม้สกรูไม้16 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ประแจเลื่อนประแจเลื่อน
ฉากรวมอเนกประสงค์ฉากรวมอเนกประสงค์
8

Cut

Lock the top down. Set the saw's depth so the blade stands 10 mm above the board. Place the board on the top in front of the blade, start the saw and press the pedal: the carriage rolls the running blade through it while both hands hold the work. Let the pedal up and the spring returns it. For ripping, leave the carriage still and feed the board.

เครื่องมือที่ต้องใช้:

แว่นนิรภัยแว่นนิรภัย
ที่ป้องกันการได้ยิน (ครอบหู SNR 30 เดซิเบล)ที่ป้องกันการได้ยิน (ครอบหู SNR 30 เดซิเบล)
9

Troubleshooting

Tube-track saw table troubleshooting.

Flow

Loading...
10

History and honest limits

**William A. Tomlinson** and **Howell B. Bearden** of Phoenix, Arizona, US 1,813,783, dated 7 July 1931, filed 5 December 1928. They claimed a top with a slot, "laterally spaced longitudinally extending tubular tracks" below it, "slotted longitudinally on their lower faces", and a saw carriage with upstanding roller-carrying hangers in the tracks, their shanks through the slots. Their saw is held by its handles; ours by its base plate. Their frame is angle iron, as ours. They give no sizes; every size here is ours.

วัสดุ

18

เครื่องมือที่จำเป็น

15

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...