การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Wood Lathe: Simple Amateur's Lathe with a Maple Bed, 7 in Swing (Lathe Work for Beginners, 1922)
A wood-turning lathe an amateur can build: two strips of hard maple bolted to maple legs make the 3 ft bed, and cast-iron head-stock, tail-stock, hand-rest body, hand wheels and cone pulleys are cast from home-made patterns. Steel spindles turn in the cast-iron bearings, and a cone pulley drives the head-stock from a countershaft.
Result: a wood lathe with a 7 in swing and a 3 ft bed.
Source: R. F. Yates, Lathe Work for Beginners (1922), Chapter XII, pp. 208-216. Unknown: the pattern sizes (on the book's drawings) and the drive. Picture: Fig. 157 of the book.
ขั้นสูง
Unknown
คำแนะนำ
1
1
Make the patterns and get castings
Make the patterns and get castings
Make patterns from any handy wood: one for both head-stock and tail-stock, with a web joining the two bearings so the casting does not spring; one for the hand wheels (three castings); one for the washers (two); the cone pulley (two: lathe and countershaft); and the hand-rest body. Give them a slight draw taper. Have them cast in iron at a foundry. Not given: pattern sizes (on the book's drawings).
วัสดุสำหรับขั้นตอนนี้:
ชิ้นงานเหล็กหล่อ1 head-stock, tail-stock, wheels, washers, pulleys, rest bodyเครื่องมือที่ต้องใช้:
แผ่นไม้แปรรูป
เตาคิวโพลา
ขนาดที่ไม่ทราบ2
2
Build the maple bed
Build the maple bed
Make the bed of two strips of clear hard maple 1 in thick, 4 in wide and about 36 in long (about 1 1/2 in thick for a longer bed), and two maple legs, the part between the ways cut exactly square. Bore a 5/8 in hole through the head-stock leg in line with the head-stock's 1/2 in tapped hole, recessed below for a nut and washers. Bolt bed to legs with eight 3/8 in carriage bolts. Sand it and give it a coat of clear shellac against warping. White oak will do if there is no maple.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็งหนา1 ways and legs
สลักเกลียวหัวกลม8 3/8 in carriage bolts
เชลแล็ก1 finishเครื่องมือที่ต้องใช้:
สว่านแท่น
กระดาษทราย3
3
Machine the stocks
Machine the stocks
Face the outside ends of the head-stock and tail-stock bearings on a shaper or milling machine. Drill the bearings between centres in a lathe with a 47/64 in drill, saw off the joining web, face the inner ends and ream to 3/4 in. Line both castings up on a 3/4 in shaft and machine their bottoms. Drill oil holes in the head-stock lugs. Tap the tail-stock front lug 3/16 in for a clamp turned, heated and bent to shape, with soft copper or brass under it; tap the tail-stock rear bearing 7/8 in, 9 threads.
วัสดุสำหรับขั้นตอนนี้:
โลหะที่ไม่ทราบ1 clamp and copper padเครื่องมือที่ต้องใช้:
เครื่องกัด
เครื่องกลึงโลหะ
ชุดต๊าปและดายทำเกลียว
เตาตีเหล็ก4
4
Turn the spindles and pulley
Turn the spindles and pulley
Turn the head-stock spindle from 1 3/8 in machine steel: 3/4 in diameter, a 7/8 in nose threaded 9 to the inch, a 3/8 in hole right through and a No. 1 Morse taper in the nose. Turn the tail-stock spindle from 7/8 in stock, 3/4 in diameter with a 7/8 in, 9-thread part. Centre each piece, drill halfway from each end with a 3/8 in drill, ream, then finish between centres. Turn the cone pulley with crowned faces, wide enough to run easily between the bearings, and fix it to the spindle with a 3/8 in headless set screw.
วัสดุสำหรับขั้นตอนนี้:
เหล็กเส้นกลมเหล็กกล้าละมุน1 spindles
โลหะที่ไม่ทราบ1 set screwsเครื่องมือที่ต้องใช้:
เครื่องกลึงโลหะ
สว่านแท่น5
5
Fit the wheels and hand rest, and assemble
Fit the wheels and hand rest, and assemble
Drill hand wheel N 3/4 in for the tail-stock spindle and hold it with a 1/4 in set screw; tap the other two wheels 1/2 in. Drill the washers 9/16 in. Bolt the head-stock down with a stud through the leg, and fit a 1/2 in stud about 7 in long for the tail-stock and a 1/2 in square-headed bolt for the hand-rest body. Plane the hand rest's bottom, drill it 3/4 in, and fit tee-rests of 1/4 x 1 in flat steel welded to 3/4 in shafting, held by a 1/4 in set screw; make several lengths. The cast iron serves as bearing metal, or the bearings can be bushed or babbitted.
วัสดุสำหรับขั้นตอนนี้:
เหล็กแบนกล้าละมุน1 tee-rests
โลหะที่ไม่ทราบ1 studs, bolts, set screws, shaftingเครื่องมือที่ต้องใช้:
สว่านแท่น
ชุดต๊าปและดายทำเกลียว
เตาตีเหล็กวัสดุ
7- 1 head-stock, tail-stock, wheels, washers, pulleys, rest bodyตัวยึดตำแหน่ง
- 1 ways and legsตัวยึดตำแหน่ง
- 8 3/8 in carriage boltsตัวยึดตำแหน่ง
- 1 finishตัวยึดตำแหน่ง
- 1 studs, bolts, set screws, shaftingตัวยึดตำแหน่ง
- 1 spindlesตัวยึดตำแหน่ง
- 1 tee-restsตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
9- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
วัสดุจากพิมพ์เขียวที่เชื่อมต่อ

การระบุ 10%
Casting Iron in a Cupola Furnace — Re-Melting Pig Iron into Finished Castings
โดย Piett
งานโลหะ
53
0
0
0
6
0

การระบุ 10%
Oak Boards and Blocks, Milled and Air-Dried
โดย Woody
งานไม้
46
0
0
0
3
0

การระบุ 10%
Mild Steel Bar Stock Forged from an Ingot
โดย Forge
ยุคใหม่
46
0
0
0
5
0

การระบุ 10%
Shellac Flakes from Stick Lac
โดย Mary
งานไม้
38
0
0
0
1
0

การระบุ 10%
Screws: Cold Headed and Thread Rolled
โดย Emma
งานโลหะ
54
0
0
0
1
0
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
